Main Features
Adjustable 4 modes:25mW/100mW/200mW/OFF
Betaflight/Cleanflight OSD configuring parameter
Support SBUS configuring parameter
Clean powerup and channel switching without interference to others
Miniature and light weight design

Specifications
Model: EWRF e7087U
Frequency: 5.8G 48CH
Transmitting Power:25mW/100mW/200mW/OFF(Pitmode)
Power supply:DC7-24V
Supply current:110mA(25mW)/160mA(100mW)/210mA(200mW)
Weight:2.9g
Size:Design for RunCam

User Guide
1.LED indication
The red LED indicates the state of working mode or the item when setting the VTX(flashing 1 time means selecting the channels, flashing 2 times
means selecting the bands, flashing 3 times means selecting the power levels).
The blue LED indicates the state of Pitmode or the value of item when setting the VTX(e.g. when selecting the channels, 3 times of flashing means
channel 3. When selecting the bands,3 times of flashing means band C.As for the item of power levels,3 times of flashing means at the power level
of 200mW)

2.Working mode indication
After powering up, the red & blue LEDs will signal the following three items of VTX in turn: channel, band and power level(the flashing times of the
red and blue LEDs indicate the item and the value respectively). After that, the LEDs indicate the working modes.
Normal: The red & blue LED are on.
Pitmode:The red LED is on and blue LED is off.

3.Setting
Press and hold the button until the red LED flash 1 time which means the item of channel selecting, then press the button can select the channels(blue LED flashing times corresponds to the channel 1-8).
Press and hold the button again,the red LED will flash 2 times which means the item of band selecting, then press the button can select the
band(blue LED flashing times corresponds to the band A-F).
Press and hold the button again,the red LED will flash 3 times which means the item of power level selecting, then press the button can select the
power(blue LED flashing times corresponds to the power level).
Finally, press and hold the button, save and exit the setting of VTX(This step is essential for setting).
Press the button twice will toggle the ON/OFF of Pitmode.

4. SBUS setting
Connected to the 6th channel of the receiver ,turn back and forth the switch can change channels. The operation similar to key trigger mode.

5.OSD setting
For Betaflight/Cleanflight OSD setting of channel,band,power and Pitmode,please referring to 'Betaflight OSD setting of EWRF Transmitter'for details.

Note:
1.Make sure that there is enough space for airflow when installing the module on the drone in case the overheating protection starts to
reduce the power even to shut down at the worst.
2. Please install the antenna before powering up for a longer use life.

Specification

General Information	Type: Antenna,Transmitter and receiver Compatible with: Vehicles & Remote Control Toys Feature: New 5.8G 48CH FPV Transmitter 25/100/200mW Support smartaudio DC 7-24V with Caddx Turbo Micro F2 CMOS 2.1mm 1200TVL FPV camera Single Size: 1.91.90.35 cm Single Weight: 2.9g
Dimension and Weight	Product weight: 0.0029 kg Package weight: 0.0300 kg Product size (L x W x H): 1.90 x 1.90 x 0.35 cm / 0.75 x 0.75 x 0.14 inches Package size (L x W x H): 13.00 x 10.00 x 5.00 cm / 5.12 x 3.94 x 1.97 inches
Package Contents	Package Contents: 1x EWRF-e7087U Transmitter, 1 x Caddx Turbo Micro F2 FPV Camera F2, Camera Accessories: 1 x Aluminum bracket,1 x FPV silicone cable (4-pin port one side, 3-pin port the other side) , 1 x Internal hexa