T Tracks 48 Inch for Woodworking by CLEAR STYLE, Double-Cut Jig Profile Universal T-Tracks with Predrilled Mounting Holes (48 Inch 4 Pack)

This is quality T Track IMO. Nice finish,accepted all my T track accessories. Enough pieces to make the 4-foot by 6-foot work table. Pro tip, if doing something like that, deduct 2 inches each way and that allows for you to cut one inch off to remove the mitered end at the edge of the table. I cut the ends with my miter saw easily and then "painted" the cut end with a black Sharpe. The intersections were a bit finicky to get set, but with time came together. A #6 screw fits fine. I laid up my table from 2X4s, so I went with a #6X1in,with the 3/8's inch dado and had a 1/8th of an inch meat left. These are the screws I used: https://www.amazon.com/dp/B0D25LX2KZ?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_3&th=1 The two included clamps were very nice , identical to a pair I bought here for Twenty bucks , so a nice value added touch. I have found nothing about this to complain about. Will shop this manufacture's brand again

I was a little skeptical and hesitant at first. How can they be so much less than the Rockler’s and Powertec’s? Also can I live with black instead of blue? Very well packaged (strong tubed cardboard held two t tracks and intersection) when I received them and a lot less wasted packaging than Rockler (plastic tube for one t-track). Tubes for the long tracks, bagged and boxed for the intersections. Strong and light. The black finish was excellent, similar to an ebony black on piano keys. Loved that there were screw holes every few inches. Had to buy my own screws (100+) at a big box store, but they are cheap and easy to find. I cut the tracks to length with a miter box jig and reciprocating saw in seconds, then a few light strokes of rough sandpaper to remove any burrs if necessary. The intersection pieces were all solid and accurately pre-cut, just align and screw in. I’d buy these again. It would be great if they offered these in other colors such as blue, red, yellow, or other t-track varieties such as double tracks or measured tracks.

Pretty good quality for the price. The dimensions are perfect. I’ve made countless jigs with this stuff and will be buying more.

Protip for mounting these, or any T-Track, read after my review... These tracks are a ok, and will do the job, but they're not going to win any awards on appearance, or continuity of quality. They are simply there to cheaply serve a purpose (especially if you lack a miter saw to make your own intersections). All in all, they could be better but they wouldn't be as inexpensive. Now for the good stuff.... Use Euro Screws to mount them! I seen Dave Stanton recommended them, and I realized the secret was out. What I did was use these screws Belle and the Yank Euro Screws 11.5mm x 6.3mm (for 5mm Hole) Varianta Style Pozidrive/Phillips Flat Head Nickel Finish (100 Pack) https://www.amazon.com/dp/B00RTMNZHW/ref=cm_sw_r_apanp_8Bmc3MFPhndEB What I do is a "Giggity" technique. It's where you flip the T-track and ream the hole just a hair larger from the rear. I used a 7/32" drill bit. It's just wide enough to have the screws threads for through, while allowing it to still sit flush with the countersunken hole. (But these tracks from Clear style might need to be redone with a countersink as they're not very straight or well made in that aspect.) This will allow you to sink them in without any glue or tape and not need to have more than ½ to ⅝" thick material under your t-track to mount. Then make sure you finish it off with the last step... tell others this technique. Then your t-tracks will become G-tracks.

Great Product, Good Folks to deal with. Thank you

Even though I had to buy different clamps these worked great.

Very nice T track at a really great price. I used these on my assembly/work table. They work as they should but as others might have mentioned it would be nice if screws were included. I used #6 x 5/8 wood screws

As described, Thanks.

Perfect

Will be using these in my Work Table as well as a couple of home-made jigs for my workshop.

Ordered after checking reviews, so understood might not be standard 3/4 inch. Was fine with that it was for a stand alone setup for a custom jig. Came fast ontime well packaged avoided damaged and bending. And it's exactly 3/4 inch and all 4 pieces are cleanly machined and finished with a nice slick surface which makes it excellent for jigs and tables. I'm actually replacing previous owned track I was planning to reuse with this it impresses me so much. The old track is going on rare use jig.

Belle qualité de produit. Répond à mes besoins.

I was surprised at the overall quality of these T-track and clamps - especially since the price is better than the other options. Solid, well made with a feeling of quality construction. Definitely recommend this product.