Snapper XD 82V MAX Extension Pole Attachment with 8.8-Foot Maximum Extension, Compatible with Snapper XD String Trimmer,Red/Black

I compare this nozzle with the one I bought earlier. My old Edger nozzle has a black painted pipe and a curved one. As well as a shaft of twisted thin rods. In the new nozzle, the pipe is straight, light and the shaft is made of a solid bar. The protective casing of the nozzle is made of metal. Knife length is 8.6 inches instead of 7 as in the old attachment. Robust and big gearbox! This is an excellent nozzle, I recommend it for purchase.

This review is for the edger attachment.Anytime I buy any piece of equipment, before I use it the first time, I check it all over and make sure all screws and bolts are tight. The first time I used it, everything was great. It does a really good job making a clean edge. Much better than the Black and Decker electric edger I've been using for years.The second time I used it, about halfway through doing my yard, it was rattling. I shut it off and went and checked out the problem. There are three little bolts that hold the blade guard on. One of them was missing and one was very loose and would've fallen out soon and the third was slightly loose. I had just checked that they were all tight when I started. Of course I couldn't find the screw that was lost somewhere along the 150ft I had just edged. I tightened the two remaining screws as tight as I could so I could finish the job.Last weekend I used it for the third time. Since I know these screws have been coming loose, I of course checked them again. Both as tight as possible. I am almost done with my yard when suddenly the blade guard is rattling violently. I stopped it and checked it. I have lost another screw and the final one was barely hanging on. The wheel that you use to adjust for depth of cut is also attached to the blade guard, so when you only have one screw holding the blade guard on, the whole thing pivots and just makes it impossible and dangerous to use.I have looked at Snapper's website and all over the internet and I can't find anything that says what the specs are for these screws. I contacted Snapper via Facebook and after a week they told me to call. When I call it says they are experiencing extremely long hold times due to the pandemic. Now I need to use the edger this weekend but I can't.So this seems to be a design flaw to me. If simply using it is going to cause enough vibration that these screws work themselves loose, that means you need to keep a bucket of extra screws for it or carry a screwdriver with you while you edge so you can stop and tighten it constantly. Looks like I'm back to using the B&D.

Purchased this after breaking two Ryobi trimmer attachments. This unit is much better quality for similar price. Using with ryobi epand-it power head. It fits pretty well, just the alignment pins don’t line up. Just have to make sure the clamp is tight and it works fine with ryobi head.

Bought this to use with my Snapper XD 82V trimmer. It's decent for small jobs. I tilled up a 35' x 10' section of yard next to my house to turn into a planting bed. It definitely got clogged a few times with larger clumps of clay. I ended up going through three 2 Ah batteries for the job, along with breaking out a mattock to pre-till some of it. Any larger of a job needs a real tiller, but I expected that when I bought it. For what it's for and its price, I'm happy.

I don't normally write reviews (I should). I took a slight gamble with this edger head as I have the 80V Greenworks line. So far I have a push mower (Costco) and weed wacker (Amazon Prime Day) in the Greenworks line. The weed wacker says it is attachment capable and Greenworks has an edger but I saw no way to buy just the head, I had to buy a whole new motor and edger head. I didn't want or need that. I have been reading that the Snapper 82V, Kobalt 80V, Menards MasterForce 80V are all made by Greenworks and most things are compatible. This went on sale for $77 and I grabbed it. It snapped right onto my Greenworks motor head and worked great. Now I can have the crisp lawn/pavement lines that drive all the bored housewives wild.

After struggling with using the string trimmer to attempt edging, I finally purchased this edger attachment.Wow, what a difference! It is easy to change over from the string trimmer to the edger and back. This attachment was worth every penny, and now I have perfectly trimmed edges on my lawn.Together with the Mower, Leaf Blower, String Trimmer, and Shop Vacuum, this Edger attachment has made me so happy with my decision to use Snapper's 82V Cordless equipment.Snapper's quality equipment has made my life so much easier.

******Updated*******Snapper has done a seemingly excellent job on this pole saw. Have not actually used the pole saw yet - so I don’t know how it cuts. I just pulled it out of the box. But build quality looks fantastic. Lots of features. Greaseable gearbox. Seriously, it has a grease zerk; I was shocked. Metal head. Metal retriever hook. Gear driven bar-lube pulp. It doesn’t get much better on a non-commercial pole saw. Can’t wait to see it cut...I finally used it volunteering at a neighbor’s who needs lots of clean up in their yard. This Snapper Pole Saw attachment ate up the oak limbs. Cut them like butter. It has an Oregon chain on it - and it cuts. Oiler woks great. Sturdy all metal construction. Greaseable gear box. Works on my Toro Power Head. Cut like a charm. If you need a reasonable pole saw attachment, this Snapper Pole Saw is it. I may order another just to have it.

... I just had to shave the length of the drive shaft by 1/8" since it protruded a bit too far to mate fully with the 40v Greenworks trimmer head... not a big deal if you have a Dremel with a cutting wheel. This combo cuts through my 3"+ St. Augustine grass like a hot knife through butter. Note that the blade that comes with this edger is not sharp... it is a fairly thick rectangle of metal, so the power head needs enough horse power & torque to spin this thing fast under resistance to work well. I've noticed that the blade tends to "self sharpen" as it scrapes along the sidewalk while edging the grass, so this doesn't seem to be an issue.

I needed (wanted?) a cordless pole saw (I have an older corded one from when we had a suburban property) The Dewalt 20v unit looked promising as I would be using this intermittently but this and the Stihl Kombi pole saw were both very pricy (I have lots of Dewalt batteries and many Stihl Kombi accessories already). I also considered a used Stihl unit that appeared to have been used commercially.I noticed this unit for a reasonable price (127cad) and it’s also articulated which the Stihl is not.The unit appears to be well constructed but the packaging looked like it had been hiding in storage for awhile. Based on the packaging Snapper is part of the Briggs and Stratton conglomerate.The unit does attach to my Kombi system but it does not have an indexing coupler or insert depth line like the Stihl attachments. I drew my own line and ensure the unit is tightened down for securing.Happy with this unit makes it easy to cut off higher branches on my acreage.Note the bar oil leaks a lot out of mine when stored even for overnight, so I empty the reservoir before storing. Due to the reservoirs location it is easy to clean and then pour back into the bar oil container (not like my chain saws).Update: I recently bought the Dewalt flexvolt trimmer with the attachment capable power head. This pole saw attaches perfectly. BTW it still works great.Update : May/21. I also bought the cultivator to use with the Dewalt power head. Works great! Not the cheapest but the cultivator is well made and looks similar to the Stihl cultivator that lists 100cad more.

I purchased this attachment to use with the Dewalt DCST972. I did find it a difficult to lock into place but it did click in. I had a small space in the garden with some small weeds to test it in. The attachment did manage to work up the soil with little effort on the "high" setting, to an acceptable depth for planting. It should work well for small gardens.

Design is good, Angled head is an improvement. Reduces chance of getting pinched.Be aware when trying to cut at a 90degree head, the power of thechain motion makes keeping chain the cut in the difficult. Instead, try 45 degrees and go gently.Undercuts same issue.Nice that this fits in the older STIHL Kombi powerheads that have square drive cables.

Thrilled to have purchased this cultivator attachment. Fit my square drive Craftsman power head/trimmer. Very durable and makes quick work in the garden.Only things I would note is that this will not tear up lawn, and the attachment is firly heavy. May need a strap or harness for prolonged use.Works perfectly as intended.