[GT-Speed] Compatible/Replacement for CS1 Style PU Front Bumper Lip, 2006-2007 Subaru Impreza WRX STI S204

Hilariously, I put this on a 2009 Honda Civic Sedan (FA5). It works with minor modification (the ends are a bit too long so you better crack out the dremel and hacksaw) and honestly I'm impressed that it fit. I bought this on the whim of the internet (the people at 8thcivic) and it looks pretty good to me. IT WILL NOT POP OUT LIKE IT WOULD ON THE STI. If you look at the pictures, you will see that it doesn't pop out near as much as the STI and that's because the left and right side are skinny and you have to move it back to get it to sit flush.PROS:good pricegreat quality (fairly thick poly walls)minor modification required (as far as putting it on FA5 body style Civic's go)CONS:doesn't stick out quite as much as I hoped (personal opinion and you have to remember it IS for a different car than what I put it on)lowers front end by about 1/2" - 1". (this may be what people are looking for but my car is already 4 1/2" off the ground to I have to place this as a con)FINAL THOUGHTS:I personally love this lip because it's the simple look that I was looking for. I'd say it's worth giving a try if you're still not quite sure about it because c'mon, it's $50! That's really cheap!

This does fit any Hyundai Accent from 2012-2017 model years. You will have to remove the factory front black air dam to install this but that's real easy as it uses screws to hold it on. You can use these same screws for installing this lip to the car. It took about 2-3 hours to do. Simply Jack up the front of the car to gain access and your ready for the installation. No modifications needed with this lip. Very solid on the car and looks great. Good luck for those with the Hyundai Accent.

I just wanted to check in to say that this fits pretty well on a 07-08 Forester XT with the Sports bumper. Don't buy the $500 STI option from Subaru, this works great for just fifty bucks. Some folks say theirs arrived in plastic wrap, but mine came in a large cardboard box and included some self tapping screws and trim fasteners. It doesn't like up with the bumper perfectly, it needs to be pulled in just a tad as it turns around the sides of the car, but it went on easily in about an hour. The ends will also stick past the front bumper into the wheel well and needs to be trimmed up. All in all, it may be one of the better purchases I've made for the car so far!

I have a 2007 mazda 6 and I honestly think this is the best lip for this car you can get especially for the price. Obviously this was not a perfect fit at all, but all I recommend is taking off the bumper, flip it upside down, and center the lip where you want it and start drilling the screws in from the center outward both sides. I applied some heat with a hair dryer on the sides which makes it bend much better. Lastly you have to cut off some extra hanging into the wheel well. Took maybe an hour and a half. Overall it looks incredible and couldn’t ask for a cleaner look!

The lip does not fit my vehicle. I have been trying for weeks to return the lip but have had no success as I have been ignored. The customer service is horrible and the product quality is just as bad. DO NOT BUY A LIP FROM THIS DEALER.

It looks pretty much like the picture except since it’s unpainted has the spotty pu look to it, definitely had to sand it in certain places that wouldn’t let sit flush with the front bumper. I wouldn’t trust the screws it came with I used nuts and washers to mount mine and 2 push clips that lined up with the fender liner clips which helped me mount it even. Over all looks good.

Fits great, looks good but you can see the injection point, looks like white lines. Still a great buy and would get it again. I may paint it in the future or plastidip it

looks amazing, but I bought it for my volvo and it is too long