Truglo TFO Tritium & Fiber-Optic Handgun Sight, Durable Compact High-Visible Front & Rear Night Sight Set, Compatible with Sig Sauer Handguns

These iron sights are some of the best I've had the pleasure of using. The fiber optics combined with tritium allow for high visibility even in complete darkness, the length of the rear sight allows for easier sight picture acquisition, and they fit onto my 320 perfectly without sanding or filing (ymmv).The length of the rear sight allows for higher precision with your sight picture when compared to the standard XRAY sights on the 320 (which I dislike due to their blocky look).I won't say they are my favorites, but I think the more I use them the closer they will be to becoming my absolute favorite. Unfortunately you won't be able to mount an RDS, but if you are looking at these then that's likely not a concern. Just keep that in mind if there are plans to use an RDS down the road.

OK, I received a TFO sight set that was obviously not fresh - the sights were loose in the package and the little elastic that is supposed to hold them was cut. The front sight was OK, the rear extremely dim - probably old product. The phone number and website Amazon gives you for Truglo are defective - 404 and "mailbox full". Amazon will NOT accept returns! BEWARE!UPDATE: once I got through to the manufacturer, they made it right - sent me a nice ew sight set, and they work great! It did take some perseverance, but the ladies there got it done.

They're great outdoors but I shoot indoor completion and they're not that good. I even tried clamping a night reading light on my pistol box to help, to no avail. Had to remove them and replace the stock sights that came with my Sig Sauer, Model P226, Legion.

#6,8 fit, but do not sit flush with top of slide. Bright site picture, otherwise only issue fit and finish.

The rear sight installed without difficulty using a B&J Machine P500 universal sight tool. The front sight, however, was a different matter. The dovetails on the P226 slide are too narrow for the new TG sight - you'll likely have to file the sight a bit to get it to install. DO NOT FILE THE DOVETAIL ON THE SLIDE. Remember that Sig recommends installing sights from L to R (as you view the rear of the slide) so pay attention to that. I used a needle file and I would recommend that you do a single pass with the file on each side of the sight's dovetail and try to install after you've completed that. Be careful, don't file too much or the sight will be too loose when you install it. You want to remove just enough material so that the sight will install without having to press it in so hard that it damages it. This is the second set of TG TFO sights I've installed, the other was on a S&W M&P40 and that installation was done without any filing at all. The sights themselves are very good - I like the improved daylight performance as well as the low/no light. I did not have to do any additional sight alignment once I had them on the gun - I got them lined up good enough on the initial install. I would not recommend attempting to install these sights without a sight press.

These sights are by far the brightest sights I have EVER had on a firearm day or night. They are brighter than my new Gen 4 Glock 22 factory sights at night, and in the sunlight are so bright they literally draw your eyes to them. I installed these on my Sig P220 and my only concern was the fact that the front sight body "floats" 0.010" above the slide. The dovetail is tight but I worry about snagging the sight. Other than this i would have given the sights a 5 out of 5 stars. I took the pistol to the range today and shot a 2.25 inch 13 round group in about 15 seconds at 21 feet. As long as I don't end up snagging the front sight off (don't think it is gonna happen), and the fiber optics stay put I'll be a very happy camper. I WILL be buying these again in the future.Here are a couple of pics:[...][...]30 year Mil and LE veteranPolice Firearms InstructorGLOCK armorerNOTE: If you are buying these for a SIG and are not an armorer, DO NOT attempt to self install them; get a professional! removing the factory SIG sights is extremely difficult without the right equipment.Here are a couple of pics:[...][...]

Glow in the dark looks really good. A little fitment work to get an exact fit. Bersa TPRC 9mm built to accept SIG aftermarket night sights. I like the bi color. Yellow and Green.

I have bought these for Glock 23 and 35 and for Sig P226.Great sights! Good visibility and sight picture day and night. These are brighter than the standard tritium sights on the P226.Saw one review where someone had problems with a set on a Sig. It is important to get the right set; there are two. One has the #6 front sight and one has the #8. Make sure you get the right model for your firearm, or your strike point will be off.Use a sight press to install not a hammer and punch. Made that mistake and broke a tritium light. Truglo was great about it and arranged to take care of it even though it was my fault. That in itself is a high recommendation. Also take your time fitting the sights; interference fit in a dovetail means flat filing and polishing to get the proper fit may be necessary just because of machining differences between firearms and sights. If you are not patient or don't have the right tools, have a gunsmith install them.Well worth the money! Once you try them, I don't think you will be happy with anything else.Forth set for another Glock 23 soon and I may attempt a custom fit job for a Desert Eagle.

Dots are bright in daylight and dusk, and installation was easy and straightforward. Tritium glow in dark is decent but perhaps not as bright as some others.

Great sights, bit better in dark. The first sight could be red or white for contrast.