0011 Digital Gauge Motorcycle Speedometer/Tachometer/Odometer MPH KM/H Universal with Multi-Function Indicator Light Display Black

Mine came with directions that were decent I guess. The set up can be a little daunting at first but it's easy enough once you get the hang of it. A couple tips to save you some aggrivation....the speedo pickup magnets work best in a tight circle rather than spread out in a wider diameter on the brake rotor. Also, while calibrating the first perameter wants you to enter tire circumference in cm and that'll get you pretty close. I then rode with a gps speedo app on my phone to compare and was able to fine tune it by raising or lowering that tire circumference a little at a time then checking again. The tach would not work when I put it on my coil as instructed and I suspect it's because of the cdi ignition, because when I put it on the positive lead straight off the magneto it worked fine, though not accurate as it's a 2 stroke and these are only good for 4 strokes as far as the tachometer goes. Otherwise, wiring directions are on point and keep in mind, for neutral and gear indicator wires, they're looking for a negative signal not positive so if your neutral switch sends a positive signal it may need to be rewired to work properly. Everything worked great though, high beam indicator, turn signal indicators, and marker light indicator all work great, even if the speedo itself isn't powered up so it saves a little power if I only want my indicators.(I didn't wire mine to the ignition to turn on immediately, I used a toggle instead as my set up doesn't have a battery originally. All my lights were added by me and run off a 12v LiFepo4 battery so my electrical set up is a little different. It also keeps it's settings and odometer memory when the battery is disconnected which is awesome since I pull my battery to recharge when needed on a bench. I actually started with 4 stars and as I wrote this review I couldn't really think of a reason not to give it 5. I feel the speedometer pickup sensor was a little touchy at first, but once I tightened up my magnets pattern and got the sensor as close to them without touching as I could, it works perfectly fine, just takes a little trial and error to dial the calibration in perfectly. There's a couple YouTube videos on installing these, but if you know a little about wiring it's fairly easy to figure out. And the included mounting bracket was very much appreciated. All in all it was a great deal for a decent all around universal gauge with all necessary indicators, even a fuel gauge. Which will blink if not used and if you're like me this may be a minor annoyance. Run a hot to the fuel gauge wire (only if you don't have a sending unit and don't intend to use that feature anyways),but be sure it's straight from the battery with a 5a fuseable link or inline fuse holder with 5a fuse and not sharing a circuit just incase you wouldn't want this thing to blow your fuse on your taillight circuit at night, I haven't blown a fuse, just not taking the chance it might. You're welcome because if it does what mine did it should just read full all the time now and no more blinky blinky. I would recommend to anyone looking to have a functioning gauge and set of indicators for a reasonable price. It's not fancy, but it works and doesn't cost a million bucks.UPDATE 10\29\21I love this thing. It took a little patience and trial and error while comparing against a GPS speedo app on my phone, but I was able to get it calibrated perfectly. It didn't take long once I took the time to do it right. I entered the circumference of my tire in mm's and that got me in the ballpark, then I just would ride, see how far off and which way and change my number slightly up or down accordingly. Got it dialed in perfect within a few tries and all is tight with the universe. I like that it holds it's settings even when there's no power because I don't have a charging system, so for one, I have to pull the battery and bring it in to charge once in a while. But also, I have a main battery switch to completely cut power to everything in case I forget to turn something off and have no lights for my trip home. The speedometer always remembers my settings and had remained accurate for months, I still pull up the gps speedo app from time to time to make sure, and it's still spot on from 1 right on up to around 50 or so where I let off because huffy beach cruisers weren't built to go that fast... I'm planning another build soon, and already have this guy on my list of materials. There's a very slim chance of me not buying another, and maybe even a 3rd for my girls bike too. Speedometers all around!!!

I gave it 5 stars because i got everything to fit up and work correctly. when entering the modes to get to your settings do not forget that if you change your tach from 1 cyl to 2,3, or 4 it will never go back to 1. Also when it says to hold for xx amount of seconds its not all that accurate, try a few different ways itll work. when i entered my tire size the spedo was way off but after a few times dialing it down its with 1 mph of my gps. it said to use 2 magnets for the spedo but that made everything all wonky and i found out i could swith the settings to use only 1 magnet. i did that and it works perfect. I was worried about the magnet flying off the rotor so i put a small dab of epoxy on it, no problems. turn signal and high beam indicators work great. have not used the gear indicator or fuel guage.5 stars

Junk your just getting it for show I have to use my phone gps speedometer I've installed many aftermarket guages and never had as many problems first of speed sensor setup is junk shift indicator only works for three gears rpm is well under what if should be incredible amount of lag for rpm and speedometer have constant power ran yet it resets to factory settings everything I turn the bike off. It's not worth the time you have to spend installing it.

This unit seems to do everything it is supposed to do. The instructions are better than most that come with these types Chinese parts. They are actually helpful. A plus is that there are a couple of YouTube videos about this unit that are helpful. The electric connectors for hook up I'm sure are fine, IF you have a Chinese clone bike that you're installing this on, if not you're going spend some time replacing the connections or using "bullet" connectors. I fully expected it to be a minor ordeal to install, but since everything works as it should it is work the money and time invested.

Not sure yet just got it today but I do see a little minor issue already. Theres no terminal connectors or plugs with wires to help with connecting. You have to hack the plugs off if you wanna do anything. If you ask me the plugs are important to keep from having to cut into any wires. Maybe it's just me being tight but I would much prefer it to come with matching mates of the plugs coming out the back. If that's the case why even put the plugs on the back of this thing. Just let colored wires come out the back and forget the plugs So it would be nice to have 3 extra plugs with matching colors on it ready to be wired that way

Excellent speedometer for my Lifan KP200 Cafe Racer! I wired up a wiring harness and a custom bracket to mount this new Speedo to my bike. All functional features of the new Speedo works great!

Highly recommend