Band-It 34250 Real Wood Veneer Iron-on Edgebanding, 3/4" x 25', White Birch

I've used this stuff before, bought from a local store. Had to buy some more for a new project, and found it on Amazon. Bought it here since I didn't want to run to the store.This stuff is pretty good. The glue is a little thick for my tastes. But it adheres well and melts pretty quick. It's a little tough to work with on curved surfaces, but something like a brayer would probably help. I just used a scrap of plywood and my hands.Also make sure to sand the edgebanding well before you put finish on it. Otherwise it's a little rough.My only last real complaint is that the rolls will usually have a couple seams in them. If you need one really long run, you might try to find something a little more high quality. The seams in these aren't totally egregious looking or anything, but you definitely wouldn't want them in an area you'll see super often.

So far I have used this on two of my projects and am happy how they turned out. Applying it to the furniture was easy and I had minimal issues. One thing I'd recommend is to use a piece of painters tape to hold it to your furniture piece after you've ironed it to help the adhesive stay stuck while drying.

The products was competitively priced and shipped fast with Prime. Product worked very well with very good adhesion when using an iron. My only complaint was the manufacturer applied an adhesive tape on exposed side of the veneer. When the tape is removed it leaves the adhesive on the good side of the veneer which must be cut off and disposed. This is approximately 1' of the product I could not use. This is no reflection on the seller as the Veneer comes in a sealed package from the manufacturer. Great product and works well.

Having ineptly assembled an Ikea bookcase with the bottom shelf installed backwards (and the fiberboard showing toward the front), I attempted to take it apart, but the back panel was nailed into the birch veneer, and could not be removed without defacing it. So, I opted to leave bad enough alone, with the fiberboard showing toward the front. Then my wife discovered this veneer strip product.In a word, it fixed the mistake I had made, and the bookcase now looks the way it should have looked from the get-go. The match is perfect. The glue on the back side of the veneer strip was sufficient to stick to the Ikea fiberboard, and an ordinary hot iron was sufficient to melt the glue.I now have a very long surplus strip of this veneer, but even if it doesn't get used, I am happy with the outcome.

I bought this to edge 3/4 inch plywood for my grand daughter project. We found you need to take off of the roll the length you need and flatten out for a while before applying. We found you best to have two people to put it on and keep it straight and even. A third person would be nice. The glue holds very well but make sure you roll or press in place as you go. If sanding after applying some excess glue that presses out can gum up your sand paper. This edging make that plywood look like a solid board. Looks great.

This was my first experience with wood veneer and it served my purposes. I used this to finish the plywood edges of an arcade cabinet. The veneer had to hold over a curve, which it handled pretty well. I went over it with the iron slowly once, applying pressure every few inches until it stuck and cooled, then reheated as necessary for a few problem areas. Overall the glue stuck well when it was heated properly and enough pressure was applied. I used two different stains on it--a dark walnut and one called gunstock. It matched my plywood, and took the stain about as well as birch typically takes stain. It brought together the two different colors of the piece very well and I was very pleased with how it turned out.

VERY good product. Inexpensive, but this stuff was the exact edge banding I needed to make my plywood look like solid wood.It’s strong and durable, the glue melts fast (so no long waiting) but also stays tacky long enough to give you plenty of time to adjust.Cuts super easily with household scissors or razor blades, but is still strong solid wood

This was very easy to work with and I was very pleased with the results using it on the edges of 3/4" Plywood. I would definitely buy this again. It was easy to cut, easy to apply, easy to align, just absolutely nothing difficult about it at all!

Happy with this product overall - goes on easily with iron and trims easily with either knife or edgebanding trimmer. Give it a nice sanding to ease the edge and you'll be happy with the results. Takes finish and paint very well!

The tape does stick and looks good too. Very easy to install.

Worked as intended. Was a bit dried out. Finished product was great

Works awesome great feel and finish.

Easy to apply. Sticks good. Good value.