Buttons Full Set for PS4 Pro Joysticks Dpad R1 L1 R2 L2 Direction Key ABXY Buttons JDS 040 JDS-040 for Sony Playstion 4 Pro Controller (Orange)

This product is great for the price! Those complaining about it not fitting clearly did not check their exact controller model before purchasing. They fit the JDM-040 controller perfectly (this refers to the motherboard model!).The feeling of the joysticks are, as far as I can tell, virtually identical to the original ones. The bumpers and triggers are also textured the same way as the original ones and I cannot personally tell a difference. However, my review is only 4 stars because the right bumper for me tends to stick when I press it. This is not an issue with the controller, as the default bumper works fine on the right side. Even after filing down any rough bits and any plastic that didn't quite match the original, I still had some sticking. My hope is that I just got a slightly defective one and that you will have no trouble, but I do wish I could use the bumpers to match the rest.The rest of the buttons feel on par with the original ones as well, though they may feel slightly different. However, the quality does not feel cheap in any way once installed.Note that the four circular buttons for the right side are slightly taller than the default buttons by a couple millimeters. This means that they do not sit flush with the body of the controller when fully pressed. In my opinion, this is a plus, but it is all about preference!Also note that the red touchpad does not appear to have any actual touchpad functionality. If you opt to install it, you will not be able to use the touchpad anymore as far as I am aware, as there appears to be integrated electronics on the original that cannot be moved. I have not researched this though so I may be wrong!Overall I am satisfied with the product, though disappointed with the sticky right bumper. It makes my controller look very nice and for that, at the given price, I cannot complain much!

All the other buttons were great! But the option and Share buttons had me up a wall. I had to shave them down after I cut the original buttons off to fit and not press the buttons. But they are also a very tight fit in the slot. They dont bounce back very well. Since this was for a gift, if she doesnt like it I will have to order different buttons.*update* I did have to replace the buttons since they werent cast well. For some reason the option button is just a hair too big for the slot and would get stuck- pressing down continueously.

I love this button kit! The pink is super cute and vibrant, and the buttons were easy to install!However, there are 2 things that I wanted to note:1. In newer controllers, the Start and Select buttons are attached to the plastic centerpiece of the controller and can't be removed. This obviously isn't an issue with this product, but do keep in mind that those 2 buttons aren't replaceable. I ended up spray painting mine white.2. This kit came with matching pink joy sticks, however these do not fit the controller well. The cutouts that slide onto the joystick modules are too deep, so they sit really low in the controller and just don't fit right. I shoved paper into the holes and was able to get them to where they are supposed to sit, but ended up swapping them out with some removable sticks anyways. Just keep this in mind.Overall, I love this button kit and I would definitely buy again!(Everything else in this kit is also from Xtremerate ;)

Most newer controllers are JDM 55 and I think most people will be curious as to whether these buttons will fit. The answer for the most part is yes. I had to sand down the touch pad for about 10 seconds on each side. It was a few millimeters larger than my current touch pad. Maybe that is the size for older models?The biggest downside is the fact that you will have to manually cut apart and perhaps glue in place the new Share and Option buttons. This model includes those buttons as physically attached to the rest of the board that the mobo sits on and I didn't feel like messing with it. It should be doable with delicate tools and fingers.Lastly, transferring the old touch pad to the new one is not doable with the tools provided. I had to use a tiny long thin and flat screwdriver I had laying around to pry it out of its old casing. You would probably snap or damage it if you attempted to use the spudger provided.I can't give it 4 or 5 stars because of the extraneous steps I had to do. Otherwise they look and feel nice and you couldn't tell them apart from being oem.

This product met my expectations pretty well. All of the buttons fit, but there are a few non usable pieces. Firstly the color touch pad. I figured it wouldn't have touch capacity, but the original touch pad has a plastic rod under it that presses the button under it. This colored replacement does not have that rod under it, so not only do you lose the touch pad feature, but the whole touch pad doesn't work as a button as well. The other gripe is that for my PS4 controller model, the share and options button are integrated into the plastic housing for the motherboard. So you cannot remove them without literally breaking them off of that housing, which I didn't do, as them being connect to the housing is how they get their spring back effect. Overall I would buy again as every other piece functions perfectly, including the triggers.

These showed up a day early, which was awesome. The buttons are amazing. Fit great, looks clean and completely colored. No spots of white or unfinished areas. But the color of the buttons are much more hot /neon pink than shown in the photo. I painted my controller with what looked like matched the picture, and when they came in, it was much more neon. An updated picture of all colors in the sale advertisement would be awesome

Thanks god. Good quality And fast dispatch