Mossy Oak Graphics - 14004-SGB [Pattern Camouflage Gun Skin Kit - Easy to Install Precut Vinyl Wraps and Matte Finish - [Shotgun OR Rifle] Kit

For the most part, it's easy to install, taking me an hour, and the video tutorial on the website is invaluable. Took a 40-year-old gun and made it look new. Great graphics, and it has held up well through hunting season. Provides an extra layer of protection as well. Guys, though I bought a new gun, an inexpensive solution to make your weapon great again!

Easy to apply and looks great

Order arrived on time. I installed this graphics kit in my Winchester 1300 Black Shadow. I must say that I'm pretty impressed given this kit was just over $20 and on prime. The BU Infinity graphics are very detailed and fine. The vinyl feels smooth to the touch and easily molds to the gun. Keep in mind that this is not going to give you the same quality as you get from dipping your shotgun, but hey, it's pretty darn awesome for the $.The installation was relatively simple. However the pieces are not specific to one brand of shotgun, therefore it takes some tweeking in order to get a snug fit. The buttstock gave me a little trouble, but I used some extra material and made it work.I would have given 5 stars if there were better installation instructions. The box points you to a rather non-detailed YouTube video that is very generic. With a little common sense you can fugue it out though. Just be sure to take your time and work the vinyl onto the gun slowly and with pressure. Clean the razor blade every few cuts with rubbing alcohol to remove the adhesive. It makes for a MUCH better cut.I would recommend this product to some looking to put a fresh face one an older shotgun with some blemishes or to someone who wants a nice looking camo shotgun minus the hefty price tag. I'm the ladder of the two.

Great product and easy to apply. Looks great

Great Product, easy to use. My gun came out great, My first time to camo my gun but should be easier next time now that I've done it once. The pic is as I was working on it, the fore stock is not done yet.

I bought this to wrap my Beretta AL390. I watched the instructional videos on YouTube before purchasing to get an idea of how difficult it would be to wrap my gun. I went into this knowing it was going to take some time, possibly an hour or two. I started with the stock and right away knew this was going to be a two hour project. It's not that it's difficult to wrap the gun or work with the material, it just takes time lining things up and working the material around the edges, and at the same time making sure there are no bubbles or creases. I used a heat gun and that really helped. I don't think it would have been possible without the heat gun (or a hair dryer). A hair dryer should also work as it should get hot enough to warm up the material.The videos mention you can easily adjust the wrap if you need to. I found this to be true, especially on the buttstock where it took a few attempts to line things up properly for fitment. I was worried that once the wrap stuck to the stock it would be difficult to remove to adjust but that was not the case. Apply a little heat to it and it pulled right off. I did use scissors to trim a few pieces and a box knife for trimming along the lines.I went into this with low expectations thinking one little mistake on my end would ruin the project or material, but honestly it was a pretty easy job and your chances of messing up a low. You still need to take your time, especially when cutting. Do not rush, be patient, and you will transform your gun. There might be some people out there that can wrap their gun in under an hour, but plan for about 2 hours. The finished product looks amazing and i'm so happy I decided to give this a try. I was thinking about purchasing a new shotgun that comes from the factory with camo, but this saved me a lot of money and looks just as good.

Worked great for my Mossberg 500

Wrap fit overall on my mossberg maverick 12ga. But it did take me about 1.5 hours to get this on and make it look good. The material is thick and you can stretch it but it does take some patients to make it look good. I would of gave this product a higher rating if it was a little more custom fit but for the price this is a great way to protect your original finish.