Hornady Cam Lock Bullet Puller 050095 - Reloading Equipment to Quickly Pull Bullets with Your Press - Save Your Bullets, Brass, & Powder for Future Loading - Uses Standard Collets (Sold Separately)

Excellent. Definitely recommend. So easy to use my daughter helps me pull Projectiles out of preloaded ammo.

Are you kidding me? Use this or a bullet hammer? Nothing could be easier for removing a bullet fro the case. Easy to use and no banging the hammer.

My rifle range isn't exactly nearby, so I make up batches at several charge weights when loading for my Garand, and trying new components, and my kinetic bullet puller was never great when it came to my crimped .30-06 cartridges. With this, they come apart easily, and no powder is lost, or risks getting mixed with anything that might have been sticking to the sides of the puller from a previous use, and it is FAST. I can probably pull a full clip of 8 with this, in less time than it would take me to use the kinetic puller for one.I use this is my Lee Classic Turret press, and it works just fine, but the hex locking nut doesn't clear the lee-style nuts of the other dies in the turret

You have to purchase collets separately. Also, it may not work for you if your pulling short unjacketed lead bullets. Tried to grab a few 9mm 115 gr soft lead bullets and it just slipped off of them. Had no problem with copper coated 125 gr round nose or truncated ones.

solid piece of metal

As someone who has reloaded for over 30 years I have made some minor mistakes. But the one I did on this one was bad...I went from .357 magnum rounds to Practice .38 SPL Rounds. But I didn't change my automatic powder measuring device on my Dillon press.......So I ended up loading 250 .38 SPL Rounds with a Heavy crimp on each one and a triple charge of powder. Bad!!...REAL BAD!I had been using a RCBS Collet puller up to this point but it took me 12 minutes to pull 2 cases......I had some hard Crimps on those bullets. I did some reading and decided to get this Hornady Puller with Collet. Boy was I impressed.... I did All those cases in 38 minutes with little effort. It's so easy to use compared to My old RCBS collet puller that I'm selling it and all my collects. If you need a easy to use, high volume Bullet puller....this is it. I couldn't recommend it any Higher! And I would buy it again in an instant! Good luck and happy Loading.

I picked one of these up on the advice of a friend. I was using one of those bullet pulling hammers to break apart bullets. I like this much better. I feel more comfortable carefully removing the bullethead in a gentle manner as opposed to putting it in the hammer and slamming it against the floor. Who thought that up anyway?I put this in a Lee single stage press. It took about a minute to install and adjust. Then I started pulling heads on my small tub of bullets that did not pass case checking. It makes the process very easy.I normally separate bullets into three categories when I reload. One are the ones that pass case gaging, they get used for matches and practice sessions. The second group are the ones that just failed case gaging, I put those into a small bin and will use them during practice sessions. Most of them barely failed case gaging so they still shoot well, but some will jam in my gun and I like to have that happen in practice (and not at a match) so I can quickly assess and clear the jam. It makes my shooting and gun handling much better and faster. The third group are the opnes that failed case gaging badly, or ones that had an obvious issue so I never even case gaged them. I pull those apart and reuse the components.

Works really well. A few trial/ errors in getting the collet to properly grip the projectile for remove. 100x better than the inertial hammer method. Marks on the pull projectile were very minor to almost none. While the provided instructions were clear, watching a couple of internet videos realy helped in set up the puller to my press.

Works as it should. Way better than a bullet puller. Less mess, quick to use, easy to set up

Benutze die Matritze um 6,5 CM und 308 win Geschosse zu entfernen. Funktioniert tadellos!

This is a great piece of kit, you need to also purchase the appropriate calibre size collet. This is far quicker and less fiddly than a kinetic bullet 'hammer' type puller.

Super !

great piece of kit,