BEP Battery Switches

Works just like OEM part. Saves you a bunch of money!

This is the perfect disconnect for your RV battery. I installed this so i could disconnect my battery from my RV when not in use. With modern RV's there is always some load when the battery is connected. One is the CO monitor, the other is the entertainment system. If you leave the battery connected and the RV sits, sooner or later you will drain the battery. Do that a few times and you will be replacing the battery prematurely.I installed this so everything in the RV is disconnected from the battery with the exception of the trailer brakes. The trailer brake breakaway switch should always be powered no matter what. It doesn't draw any power from the battery unless the pin is pulled out so under normal conditions this will not have a negative effect on the battery charge.These are well made and easy to operate. Installation isn't difficult but you do need to have an understanding of what you are doing. There are no instructions per se because it is a universal part.If you know what your doing, or have someone who does install this it is a great option.

I installed this to be a cut-off switch for dual six Volt batteries (wired in series for 12 Volts). I had just enough room to mount it in the top of the battery case. The trickiest part was figuring out where to drill a hole so it would be close to the edge and still work and allow room beneath for the battery.The switch operates smoothly. Given that it is waterproof, I expect it to give long service. This is a solid, substantial feeling switch. Since the handle is exposed, it is attractive enough that I don't mind it being there.Negative: When it arrived, the plastic display bubble was cracked. I did not notice until later that there was a small chip in the finish where the bubble was cracked. Whether this happened in shipment, or whether it was that way and shipped anyway, I don't know. It was very minor, in an area that is hidden, and not worth the hassle of returning, especially since I needed to get it installed. The very minor flaw does not impact operation.

I bought this switch to install on my RV's battery case, so that when I store it between trips, I don't have to physically disconnect the battery. When I first received the switch I was disappointed to find that it was open on one side. Although this opening is designed to run the battery cables through, I had hoped to install the switch on top of my case and enclose all sides for a watertight installation. I planned to run the cables through a hole in the top of the battery case, place the switch over the hole, and seal it on all sides.In the end I realized that just mounting the switch on the side of the battery case with the open side down would offer the same level of protection as the battery case itself offers. Installation was easy, although I had to buy both a connector cable to run from the switch to the battery, as well as the mounting hardware. I did seal the removable side panels with clear silicon sealant.With the disconnect switch installed, I now only have to turn the switch 90 degrees to disconnect the battery from the camper. When I get ready to camp again, I flip the switch back and restore the connection. My battery is still fully charged since it hasn't been drained by the CO2 detector, radio power LED, fridge LED, etc.If desired, the switch's knob can be removed by pressing it slightly and rotating it 45 degrees counterclockwise. However, I'll probably never use that feature.This is a great product that does the job for which it is designed. However, I'm giving it four stars because of the time and expense involved in buying the mounting hardware and the connector cable. Yes, I knew when I ordered it that those items were not included. However, the value of the switch is lowered by the additional time and money required to secure the items needed for installation. Had they included these items, even if they charged a few dollars more, I would probably give it five stars.

Great battery disconnect. The removable/configurable side panels are great for adjusting to your particular cable routing situation. It is a well made switch with a large easy to grip knob. The switch positively locks in the on/off position. The base cover is great for covering the studs so the lugs and studs can't contact mounting surface and short out. I was able to mount the body using 10-24 Phillips head machine screws. The body has a recess in the mounting holes and the Phillips head screws were completely seated in it. There is small wording at the base of the knob that says either on or off depending on which position it's in (on background is green, off background is red). You would have to be pretty close to the switch to be able to see it. It's a compact switch that works great at a good price.

I used this to cut the battery power to my travel trailer. The goal is to keep the trailer from draining all the power from the battery when it's not in use. Very easy to install on the plastic battery box lid. It will take a few hours to do if you want it to look good & if you want to flush mount it. I used a Dremel to cut the hole. Before you cut, make darn sure you have your measurements right. I got in a hurry & cut the hole too big on my existing battery box & had to go buy a new one. Below is a list of what you'll need to do the job. Regarding the screws I used, I went with 3" screws & cut them shorter with the Dremel once I had everything mounted. Be sure to cut the screws AFTER you mount the battery switch & tighten the nuts.LIST OF ITEMS YOU NEED FOR FLUSH MOUNT:1. Measuring tape (for flush mount hole).2. Red 3/8" Stud 12" Long 4-Gauge Battery Cable.3. Four 10-24 x 2.5" stainless screws.4. Four #10 stainless flat washers.5. Four 10-24 Stainless Nylon Insert Lock Nuts.6. Water sealant to apply around the outside of the switch.That's it!!!

Practico y de buena calidad.

I use this as a disconnect switch on my motorbike. It seems sturdy and simple to use. Pricey but all niche products are.

Lo instale en una lancha para llevar 2 baterias y tras 1 mes de uso va perfecto

Exact replacement of the existing one. Short shipping time

Muy buen equipo desconectador Principal lo utilice para un Sistema Fotovoltaico para desconectar las Baterias.