Woodland Scenics® Hot Wire Foam Cutter

This worked wonderfully on styrofoam, cuts like butter! Great for crafting play sets.

Worked like a charm on my Pelican gun case. At first the wire kept breaking for me while using the collars, I found that by just using the wire around the actual prongs in the grooves worked super well. Only like 3 twists per side. To get proper tension I found that squeezing the prongs a bit while twisting worked well, then letting go for proper tension (doesn't have to be stupid tight)At first I wasn't sure about the wire... I even ran to home depot and wally world to try and find some "resistance" or "nichrome" wire, with no luck. NEITHER STORE SUPPLIED THEM. I got fishing leader but ended up trying the supplied wire one final time when I got home (this time without collars) and it worked for the duration of the mag cut as well as the actual gun with only 1 retie due to trouble reaching. near the bipod. You'll probably need a second set of hands to push foam around for some cuts...the thing doesn't have a huge space between handle and wire.See attached pic for quality. Also be sure to run the unit level or you'll get sloppy cuts. I found a big table with lots of clear space to work well. This was my first time using a foam cutter and was very impressed after all the skeptical reviews. Other people may have got duds or tried going too fast or didn't take small 5 second breaks after 6-12 inches of cutting. Take your time and it will probably look even better than mine!I'll be doing my dad's case after he orders replacement foam due to the sloppy cuts the first time with a utility knife. Solid product so far.

I finally got a chance to open the package, to use my new hot wire foam cutter.And it did not work at all.It’s junk!! It doesn’t heat up at all!!!Be sure that if you buy one, test it right off the bat dont wait to try and use it!!!

No complaint here, just a good product.

works so much better than I thought it would, I am making 3D wall art with RD-50 insulation foam board for my daughters room and thought this would be a much easier less messy option than the sawzall I had been using, but was not sure if it would cut well with this particular type of foam board considering it was not intended for hobby/craft type use. But it worked so much better and even beyond my expectations! I thought the push to heat trigger would be very irritating and even imagined I would have to tape it down before I even got it, but sure to their word it heats up instantly ready to cut at a push and cools down equally as fast (Please do not test this by touching) as it is not instantaneous. I give this product 5 stars for it's quality feel does not feel like cheap plastic, also it works just as stated on it's advertising which these days getting junk from companies is just par for the course so this was a nice surprise.

This is such a great foam cutter that I would give it 5 stars if only it worked consistently. The power adapter port on the tool is so poorly designed that it doesn't fit securely and gets slightly loose as it is used (even for a few minutes). The tool then turns off without the user realizing and stops heating and gets stuck in the foam. It's hard to tell if the cord is plugged in securely. So much trouble for such a simple tool!Edit: I was so frustrated with the way this tool was designed that I performed surgery on it. The yellow slide switch has to be held with a great deal of upward pressure to keep the power on.So I filed down the power plug port to make it fit better. And then the real surgery began. I de-soldered the yellow switch and found a pressure switch that is easy to press down and hold in place. I tested the circuitry to make sure the new switch would power the tool and then soldered its wires to the existing power wires. I used a scroll saw to cut a larger hole for the switch in the tool's plastic casing and then hot glued the switch in place.When I re-assembled the tool and tested it, it worked great! My photos are above... I'm hopeful the engineers who worked on this tool will take some of these improvement ideas to heart.

This was my first experience with a foam cutter and I was pleasantly surprised. This unit works as advertised. Minimal assembly is required, you install the two arms, string the wire across and you are ready to cut foam. Just plug it in, pull the trigger and in about 1 or 2 seconds its hot and ready to cut. It was very easy to use and literally cuts like a hot knife through butter, was even able to melt through glue joints made with Gorilla Glue! You do have to hold a trigger down to make it cut, but it wasn't hard to hold down, even on long cuts. Two thumbs up, works great and you cant beat the price!

Slices through foam board like butter love it