VR Cover for Oculus™ Quest 1 - Washable Hygienic Cotton Cover (2 pcs)

They don’t fit perfectly. While wearing them they fall off and need constant readjustment. Will be returning.

I tried this cover and two other styles/brands of cover. The key feature that made this work for me during my VR workouts is that it wraps around the bottom of the forehead section of the mask which keeps it from riding up my forehead. Thus it keeps soaking up sweat where it needs to and I don't end up with sweat in my eyes or lenses during the workout. The fabric used in these, while less appealing to me initially due to its texture, was also much more absorbent than the other brands I tried and I think it's the texture that helps that by distributing the moisture through the cover rather than ending up with sopping sections and completely dry sections. I'd give it 5 stars but I do wish the bottom portion covered a bit more of the face towards the nose. That may be a feature though, I haven't found any coverings that cover that section and it may be to keep breathing clear as I do sometimes feel my headset weighs down on my breathing through my nose.

Warning, doesn't fit the stock interface very well.The elastic straps that are supposed to hold it to the facial interface, actually stop the interface from clipping into the quest correctly.The material itself is nice and soft, does feel nicer than the stock foam alone.Because the elastic is so poorly implemented, the cover doesn't stay taut/ fit correctly.... leaving creases, which then press hard into your face, making it even more uncomfortable than the stock interface alone.I've amended this review from 1* to 4*.... simply because, when attached to the actual vrcover facial interface with their foam, it fits WAY better. It's a tighter fit and the material spreads out a lot easier.... since using this with my other comfort mods, I don't get "oculus face" anymore. Feels nice and you get 2 in the pack.

The media could not be loaded.  I have had my quest for some time now and put a lot of hours into it. My main issues when using it are the light leakage around the nose and the fact that if I pull the quest a little bit away from my face I seem to get a better image (despite messing with the sliders and vertical position).I therefore decided I needed a batter face interface pad which was perhaps a bit thicker. It would also be a bonus if it reduced the level of red pressure marks on my face! Having watched someones YouTube video, they mentioned VR Covers and mentioned a really good replacement interface with pads. I knew this wasn't exactly that piece but through looking at the images that it might provide some of what I was looking for. With no other reviews I was on my own buying this one! (this is why I write reviews, they are so helpful in deciding what to buy so I like to give back).What you get:- A few cleaning pads... no idea why you would need these when the point is you are buying a washable cotton cover. You can really 'wipe' a cotton cover, so maybe they are for the controllers?- Two cotton coversThe cover goes on fairly easily (see my video) and adds some additional comfort. But there is very little to this product and at essentially £12 per cover I really cannot call this good value. I could probably sew my own for far less.Pros:If you want a swappable face plate cover so you can clean one while wearing a fresh one, then yes this will do that.Adds a little extra comfortMinor reduction in light leakageCons:PriceNot for sharing the quest really. Its just for personal changing one and washing the otherIf you found this helpful please do let me know by clicking the helpful button as it encourages me to spend the time writing these reviews and filming them.

I bought a set of these covers to put over a silicone facial interface cover. When I sweat, the silicone cover tends to slide easily, even with tight headstraps, so eventually, the quest would slide down my face. I figured I would put a cotton cover over the silicone to absorb sweat and prevent the sliding down aspect.It did work, but there are caveats.The cover fits over the silicone cover, but the elastic for the nose will not work as intended; It's rather tricky due to the flaps on the nose piece on the silicone cover. There are two options, you can either trim off the flaps and deal with light bleed, you can leave them in place, attach the elastic as described, but the bottom will not be fully covered, or you could replace the elastic with a longer piece. either way it will take some modification.Airflow will be reduced a little, My lenses haven't fogged up, so it's not an issue for me, but it may cause issues for others. If you use only the factory interface, these are perfect.If I find a good solution for silicone cover users, I'll update you.