7594SRS Arbor One-Handle High Arc Pulldown Kitchen Faucet Featuring Reflex, Spot Resist Stainless

This Moen faucet (which was made in the U.S. and shipped to Amazon Germany) is equipped with U.S. standard-type threaded 3/8" compression water connectors. These are NOT compatible with European water connector standards, so the water connections to the faucet cannot be accomplished. Also, adapters are virtually impossible to locate in Europe. Amazon Spain does not convey this info on their purchase page.

We love this faucet. It looks great, works great, and it was easy to install. We have much better water pressure with this faucet than the faucet we had. The only thing I would complain about is any water you get on it or the base leaves spots when it dries, but that's just nit picking. Overall, I am very happy with the faucet. I do feel it's a good value for the money. It was less expensive on Amazon than our local hardware store. I would recommend.

Muy buen producto y a un increíble precio. Luce bien y funciona de maravilla. Mi recomendación es que tengan buena presión de agua o presurizador ya que no está hecho para baja presión. Se puede instalar en un horificio o si tiene tres trae su placa para que los tape.

I absolutely love this faucet! The pull out hose is great for cleaning fruits and vegetables, washing dishes and cleaning the sink! When you switch from stream to spray, you can adjust how hard the spray is and you can move the faucet head to be as close or as far away as you need it to be. (Keep in mind that the switch from stream to spray is regulated by water pressure. So, you can't turn the water down to a trickle and expect the spray to stay on.) You can have it turned on pretty low though. We have to turn ours on about 1/4" of the way to full open before we can get the spray to stay on. But that is just about perfect for the spray pressure when you want it soft, and it works great! It is very easy to install, looks great, and works great! The reflex works wonderfully. If you need the pull out extension to be short for a single basin sink or long for a deep well double basin sink, it works either way. You decide how long you want it to be. The faucet comes with a weight that you simply clip on the pull out hose under the sink, which determines how far you can pull the faucet out and how far back it reflexes. The only caution I have for you on this is that if your sink plumbing is a mess, like mine, the hose and weight will hang up on it. If you don't fix it, this will render the faucet extension useless. There is an easy fix though! We simply used an old piece of cheap poster board and some painters tape to make a channel along the back wall of the sink cabinet for the weighted hose to slide up and down. By containing it in the makeshift channel, it can't hang up on the other plumbing and it works amazingly. My only other caution is for people who are replacing a 3 hole faucet. This faucet is much shorter than the old faucets were. There is only 3-1/2 to 4" total length on either side from the center hole on the trim kit. So, you can easily change your plumbing set up for a single hole installation, but the trim kit may not cover your old holes. We just used the single hole faucet assembly (without the trim kit). We put it in the hole that was best for reaching both sink basins and then bought 2 cheap 2 inch hole cover blanks to cover the old holes. You can spend $20 or more each for hole cover to match the faucet, but we just used cheap plastic hole covers and it looks fine. We installed one of these for my mom over a year ago. It is still looks and works like new! It was so nice, that when our old faucet crapped out a few months ago, we decided to get this one, too! And as an added bonus, it was actually $50 cheaper than the non-reflex (pull out) version. And it's Moen, so it has a lifetime warranty! Highly recommend!

Comes with special installation tool and base plate not always required.