Rubber Monogrip Revolver Grips with Finger Grooves for Ruger SP101, Black - 81000

I recently purchased an SP101 2.25" and was having trouble with getting a proper grasp. I'm about 5'10", my fingers are relatively long and thin, so with a good tight grasp on the stock grip the trigger was in the middle of my second phalange. My pinky always ended up dangling off the end of the grip even though my hands are not particularly wide. Managing recoil with 38 HP 110gr wasn't terrible, but 357s of any kind were hand-numbing and difficult to get back on target. I saw similar complaints online, so I decided a grip replacement was in order. Installing this grip only took a few minutes, including removing the old one. The adapter and pin went on the frame easily. It was a little tight to slide up the frame, took a little wiggling to get the adapter lined up in the grooves, and the rubber wanted to catch on the hinge pin tab so I had to walk it over. All-in-all, maybe five minutes. The grip mates nicely to the frame, feels tight whereas the stock grip seemed a little wiggly by comparison. Looking at it you'd think it could just as easily be stock unless you already knew. After taking it out shooting a few times, I can say the Hogue grip makes a world of difference, and is a fantastic value for the price. It properly fills my hand, my trigger finger ends up hitting the trigger on the last phalange correctly, I can get a full grip with my pinky, my hand aligns better so the hammer is easier to pull back for SA, DA trigger pull is steadier, recoil is much easier to control with hot 357 loads and doesn't leave my hand buzzing. Overall my range experience (as much range as you get with a snub nose) has improved significantly since upgrading with this grip. This may as well be considered a necessity for the SP101, unless you have very small hands in which case the stock grip may work for you.

I recently purchased a Ruger SP101 3" .357 and the stock grips are very hard plastic/rubber that can become very uncomfortable to hold/grip after some time or even a few hot .357 loads so I decided to buy these as they were very highly reviewed. The Hogue grips are extremely comfortable, they have finger contours for added comfort and this makes shooting the Ruger SP101 much more pleasureable without a doubt. A Must buy for the Ruger SP101. Hogue rubber grips are molded from a durable synthetic rubber that is not spongy or tacky, but gives that soft recoil absorbing feel, without affecting accuracy. This modern rubber requires a completely different molding process than ordinary neoprene and results in a much superior grip. The material we use does not come apart or deteriorate and is resistant to all solvents and oils used around firearms. Hogue Grips give you a lasting precision fit and durability that will provide years of dependable service. The flexibility of our materials and molding process has allowed us to produce superior rubber grips with features that out perform all other makes. HIGHLY RECOMMENDED! ------------------------------- PROS ------------------------------- * Price Price Price Price * Build Quality * Comfort/Ergonomics * Rubber to better handle/grip ------------------------------- CONS ------------------------------- * None, they are awesome!

I have a GP100 and got a new SP101. Took it to the range but was not very happy with the stock grips, wanted something similar to the grip on the GP100. These are very similar to the GP100 grip but a bit smaller of course. Very easy to install, hardest part is honestly removing the old SP101 grips. Just unscrew the old ones, pop out the sides, remove the pin, and slide off. Then put the included bracket where the pin was, slide the new ones on, and screw in to the bottom. The fit is perfect, and the grip feels much better in the hand. It has finger grooves like the GP100 grip, and I can tell just from holding it that it will absorb more recoil. This grip also works better than the stock grip with HKS speedloaders which is a huge plus. They are slightly bigger, but definitely seems like a worthy trade off. Excited to try them out at the range.

I have had a 2" .357 SP101 for about 10 years now, and like it a lot. The only gripe I've ever had is the sting in the palm of my hand when firing .357 rounds. It has always caused the "web" of my hand between my thumb and index finger to get sore. I figured that's just the way it is with a small-framed powerhouse, until I got an LCR. It is much easier on my hands (though kicks up a lot more). I believe this is due to the Hogue grip on the LCR, which is why I bought this one for my 101. I have not actually shot it to confirm the impact to my hand is reduced, but I am very pleased with the fit, the ease of installation, and the price. The grip also feels better in my hand, because I really like grips with the individual finger notches. This grip is definitely bigger than stock, which may hurt pocket carry. It did not impact my ability to use a speedloader. Though you can't seat it all the way flush to the cylinder. But I can't do that with the stock grip either, and it is no worse now. Update: I have shot some magnums with this grip, and I still get that impact in the "web" of my hand. It's hard to say if it is reduced, but it's definitely still there. That said, I still prefer it to the semi-rigid stock grips.

Best there is...great product.

Fit perfect look great

Easy installation. Excellent option for a larger hand over factory grip

Makes holding it very steady, great product

I chose this grip with no reference as to its actual size. I am a male with medium size hands. When I received the grip I was slightly disappointed that it was smaller than expected. However, it is a big improvement over the SP101 OEM grip. It does provide a larger area for my fingers (pinky no longer hangs off the bottom), a thicker grippier palm and I lke the finger divots. The grip also fits my SP101 like a glove, 'looks like it came this way from the Ruger factory. Took me less than five minutes to install.