GPU Holder Brace Graphics Card GPU Support Video Card Holder Bracket with 5V 3 Pin ARGB LED, Video Card Sag Holder/Holster Bracket Support RX6700,RTX3090- 309EZ-Black

The EZDIY-FAB GPU Holder Brace Graphics Card GPU Support is a practical and cost-effective solution that helps adding extra support to the GPU specially when you plan to ship it or move it around. Here are some key points based on my experience:Pros:-Sturdy Construction:Seems to be made with high-quality aluminum, which in theory should help to prevent sagging and potential damage to the motherboard PCIexpress port.-Adjustability:I really like that comes with two different adaptars that will allow you to adjust the holder potentially accommodating a wide range of GPU sizes and configurations.-Aesthetic Appeal:Even though so have the logo showing, I think is still not that bad on the overall appeal.-Ease of Installation:The installation process is straightforward and doesn't require any special tools.-Cost-Effective:So far the price felt about right, hence is a value for money.Cons:-Fitment Issues:Since we will always have particular cases with unconventional layouts or limited space. It's important to check the dimensions and ensure compatibility with your specific case.-Limited Color Options:The color options for the brace are somewhat limited, which might not suit everyone's aesthetic preferences.-Support for Ultra-Heavy GPUs:The mean reason for the purchase if for having a cost-effect and stury GPU holder that will be able to support up to RTX 3090/RTX 3090ti, but not the heavy and large RTX 4000 series cards.Conclusion:Overall, the EZDIY-FAB GPU Holder Brace Graphics Card GPU Support is a reliable and stylish accessory for most PC builders looking to prevent GPU sag. Its combination of sturdy construction, ease of installation, and visual appeal can make this a popular choice among gamers. However, potential buyers should consider their specific setup and compatibility needs, especially if they have particularly large or heavy GPUs, then you need to consider the EZDIY-FAB GPU Holder V2.

The design is simple but effective. Workmanship of the product is good. All the needed screws are included.It isn't that too difficult to install however since this is after every thing else in the system was already installed in my case it might not be as straight forward. Mounting the main blanket may need two hands as the bracket is long as it trends to tilt away from the hole to put the first screw in place. This was at least this for me. Once you get at least one screw in place in the back slot then the rest is one hand operation and simple.The rest is straight forward. However, you may want to try to test fit first with loosely screwed so that you know where to position the small supporting piece. There are two supporting small brackets with the kit. You need to see which one fits you the most. Next you need to know where on the main bracket you want to put the supporting bracket to screw on to so that the supporting bracket supports the flat surface of the GPU card. For Asus TUF 4070 OC card, I choose the middle two slots of the main support bracket which lines up with flat position between two fans perfectly. Also note that, the small bracket is an "L" shape. The lag of the "L" needs to face out toward the side of the closet case for line up with flat surface of the GPU card. I first put on with leg of the "L" face inward toward motherboard and that is too far into the GPU and it does not line up with the larger flat surface between the two fans.Last, you need to adjust the height position of the "L" bracket so that it touches or fully support the GPU card without gap. Once you've found this spot then you can hand tight the two screws to keep the "L" bracket in position.This is to it at least for the two slot graphic card with fan cover housing similar to to Asus TUF 4070 card which should be most of the GPU cards currently. Check this first however.An improvement would be allowing "continuous" position of the "L" bracket on the main bracket to adapt to more variety of GPU card design as opposed to currently the "L" bracket can only go in to those 8 vertical slots and nothing in between. Two horizontal slots along the length of the main bracket might address this. This is the concern that I had when I first try to install the kit.Aesthetically, the main bracket has 4 decorating shiny chrome screws. Those look nice against black bracket. It makes the whole contraption more like a construction in a space ship.One thing that is not easy to determine is whether the bracket creates any issue with air flow around the GPU card or not. The main bracket creates a partial channel that runs parallel to the depth of the case. This might impact how GPU's fans pull air around them. Now with the main bracket somewhat blocks the open space from without the kit installed. Hope this doesn't create a heat issue. Otherwise, a verticle might be another option (but more expensive one).

This is a simple solution for a minor problem. My gpu (Gigabyte RTX 3060 Vision OC with 3 cooling fans) was sagging a bit, and this support brace works great for remedying this annoyance. The aRGB lighting is nice for blending in with the system, and in my case doubles as an effective way to block an unsightly wifi pci-e card and helps to hide the gpu wiring.The brace includes 2 different support pieces for varying heights, and also 2 long and 2 short rubber pads that are peel-and-stick design allowing safe, insulated contact between the brace and the gpu. This eliminates any potential fan vibrations transferring to the brace and case. The multiple support mounting slots allow a wide range of adjustability for location and height of the support.Overall I would like to give this brace 5 stars, but the color is more of an off-white which is more noticeable when placed in the white case; thankfully, I have a few white led strips in the case for general lighting that really help to blend the differences and make it not noticeable. It's also worth mending that the wire for the RGB lighting is black, even on the white brace. Not a huge deal for me as my case includes lots of white and black, but could be an issue for a mostly white build.