Mr. Super Clear Gloss Spray

Finish is outstanding when done properly. Gives Gundam a higher quality look

Why did you pick this product vs others?: I am so impressed with this clear. GSI Creos always has the best products. Highly recommend this item.

I use this to fix doll lip chips.

Probably the spray I have ever used

Hard to find at hobby shops, shipped quickly 👍🏻

After using this on several projects I have to say it’s only so-so. As far as being easy to spray, it’s on point. Goes on easy, flows out nicely, and it dries nice and clear with no milkiness. However, it dies back somewhat once it cures and doesn’t leave as smooth a surface once cured as it has when it’s still wet. You’re left with a little bit more of a grainy surface than you’d expect. A light color sanding and polishing gives a good final finish and it polishes well, but comparing it to Tamiya TS-13 it just doesn’t measure up.

If you're looking for a spray coating that is really good at doing exactly what it needs to. This is it. Coats super easily, dries extremely well, doesn't take too long (times below and notes), the finish is immaculate. Generally for small and light spray items - 20-30 minute dry time For medium esque items to a bit large 40-1hr Large and anything beyond 1.3hr+ depending how much spray was needed to coat. LEAVE OUTSIDE/OPEN/EXTREMELY VENTILATED AREA. DO NOT INHALE. The fumes are strong and gross and just overall not good for breathing in. The smell after drying will still be there a bit but nothing unmanageable. DO NOT- spray in rain or decently high humidity as the water messes with the spray and coating. Try to find a more dry space while using.

I've been using Tamiya TS-13 for years on my Gundam model kits, but as I paint more and more on them the cost of that product was beginning to get daunting. This was appealing due to being marginally cheaper for a similar product, plus the can's bigger so there are less of those to keep around at once. It may just be my new go-to on Gunpla. It sets quicker than Tamiya TS-13 and was a little easier to apply uniformly, but that latter statement could always just be operator error on prior builds. I have a bad habit of putting coats on too thick and this was unforgiving to my thinned-enamel-based panel lining which started to run badly into places it shouldn't have been when I inevitably put too much on one area, so there was a prominent spot that I had to fix up after the initial coat. This proved easy to fix by just using some of this same company's lacquer thinner, so that's another plus but it feels like the Tamiya product is more forgiving in this regard. Matte coats have always been the popular preference in this hobby but as one of the outliers that likes the clean, polished up look of a nice gloss coat, this does the trick very well.

良かったです

Modelling products

جيد جدا

・光沢 ラッカー系塗料でメタリック塗装した仕上げに軽く吹いてあげると、キラッキラに仕上がってとても良い感じです。 筆塗りでも、塗りムラが消えて綺麗な光沢ができるのでとてもオススメです。 ・半光沢 ラッカー系メタリック塗装の上に軽く吹いてあげると、程よく金属感が出てくれます。あまりギラギラさせたくない場合にどうぞ。 ・つや消し かなりマットに仕上がります。ラッカー系筆塗りの仕上げに使うと塗りムラが綺麗に消えるのでオススメです。 注意点としては、未塗装の状態で吹くとPS素材でもかなり脆くなるので、そういった場合は水性のスプレーの使用を推奨します。また、水性塗料で塗装した場合も使用は推奨しません。この場合も水性のスプレーの使用を推奨します。

UVレジンのコーティングに向いているというレビューを見て購入 他の塗料よりきれいに平滑に塗れました。液垂れもなくきれいです。 サンドペーパーも適度にかけ二度塗り、艶も適度に落ち着いていいです。 但し気になる方がいるとしたら、しばらくすると当初の艶より少し落ちます。 また内容量が倍くらいのものが欲しいです。