BiMi 50137 Replacement Office Chair Tilt & Lock Lever Base Plate Mechanism Large 150x255mm

Fabulous item and really easy to fit. Saved me a fair bit in having to purchase a new chair. Well worth it.

All 4 holes lined up with my chair holes perfectly, very easy to fit and install, 15mins and fitted!Rocking function is exactly what i expected 5 degrees is good gives with a decent amount of rocking travel to relax sitting in my game chair.- the friction/ resistance rocking control knob is easy to turn to the desired setting works well very easy.solid steel construction wont bend or distort.price is ok and what i would expect to pay for a solid steel well-made Plate Mechanism'would recommend.

After my (expensive) gaming chair broke I didn't really want to have to replace it. I was very pleased to find out you can get spares for gaslift chairs. It wasn't too tricky to fit although its a heavy unit. My Arozzi chair is useable again and it didn't cost me an arm and a leg.

Amazon added a flag to this that it is frequently returned because of the size. I used the dimension sheet in the product image listing and that helped me to see that this would have been a perfect fit. As stated by other reviewers, I also purchased a hammer to get the old base off and very easily installed this in a few minutes. Does its job well and fit within my budget (£25). I've seen quite a few reviews talking about the welds having a 2 year life cycle. I guess I'll be back in two years (or less depending) to report my finding.

Bought this as a replacement for the tilt and lock lever base plate mechanism for my Cherry Tree office chair. Reason for replacing it was the gas lift had stopped working so I had to replace it with a new Tuka gas lift. However, while I could remove the bottom end of the old gas lift from the wheel base of the chair, the top end was firmly wedged into the base plate and simply would not come loose despite using plenty of WD40 and trying to knock it out with a hammer and rubber mallet. In the end, I decided to stop wasting my time and purchased this new base plate which fits into the bottom of my Cherry Tree office chair perfectly with all the screws lined up nicely. The Tuka gas lift also slots into place perfectly and I now have a chair which works great. Height and tilt work nicely and the chair is solid and sturdy. Been using it on my chair for 2 weeks now and have had no issues with it whatsoever. A great buy.

Great quality and works exactly as expected. Very easy to assemble and when fitted was very sturdyEdited 02/05/2025: the middle where the piston connects has worn down and warped, it would appear that it’s not for people my weight.

My old, and rather expensive, chair was on its last legs. It was hanging on like a loose tooth hangs, one sharp movement and it was going to be game over. So, balancing as carefully as I could I sat on it and did some research and found that my wobbly chair was most likely caused by the failure of this part. I bought it, got it next day, Saturday, thanks to prime. Put it to one side as it was going to be a job to do mid week. Well the chair had other ideas and upon seeing I had bought a new part it decided to fail in dramatic fashion dumping me and my heavy set figure on the floor. What Luck!, well not exactly the words I used at the time but still, I am glad it waited for the part to come.Super duper easy to fit.Get a hammer, because you are going to have to knock the old on off most likely. Just keep sliding the hammer up the pole, tapping the bush that is still on. Turn it as you go, oh, and make sure you are not aiming it at anything breakable because it will probably shoot off with a ping when it finally goes. Turn tap, turn tap, turn tap.... ping.Take the bolts out of the old one on the bottom of the seat. Shove this on in its place, making sure you have it the right way around or you will spend the rest of your computer time sitting like the Fonz (for the kids out there, this means backwards on your chair looking cool).Once it is bolted on, just put it over the pipe, push it down a bit and sit on it...congratulations, you have just fixed your chair... Mine was a £200 chair so as you can imagine I am extremely pleased... and proud too of the handy little job I have done.Good Luck, and remember to measure before buying.UPDATE... 11/12/15 --- Just over 12 Months and still hasn't dumped me on the floor yet. Just weighed myself and I am 18 stone, or 115kg for those modern folks, also keep in mind that I often fall asleep in my chair, reclined with my feet up on the desk so I am not exactly giving it an easy life. There is a little bit of a wobble now, but nothing serious. I reckon in about another year (2 yrs total) it will be time for another repair,,, unless I lose a few inches of flab in which case I might get longer out of it.

Disappointed