EKWater Blocks EK-Cable Y-Splitter 3-Fan PWM Cable with Sleeve 10cm, Black

Does what it's made for and is of very good quality, the price asked is very reasnoble.

I replaced the stock fans of a Corsair H150i Pro for 3x BeQuiet! Silent Wings 3 (high speed model).The Corsair fan controller is meant to be for lower RPM fans and l'm guessing that's why it fails to control the SW3 fans properly. That's where this EK cable splitter comes in and it does the job as intended.I plugged all 3 fans to the cable splitter and then the PWM end to the motherboard chassis fan plug. I can now control these fans at will via Asus BIOS (Fan Xpert and l are not in good terms).Other than that, l'm always 'highly' reluctant to buy a product sold by a 3rt party company (a.k.a Amazon Marketplace). In this case, the seller is "CCL Computers" and all l can say is l had a fantastic experience (i.e. right item, factory sealed and super fast shipment). Thanks "CCL Computers."*Just to clarify: the cable splitter consists of one 'PWM' end (4 pins) which you connect to the motherboard and 3 separated cables where you connect your fans. Of these 3 cables, 1 has 4 pins and the other 2 have only 3. However, all the 3 fans connected to the cable follow the 'PWM' signal sent by the motherboard.You could plug 3 pins/non 'PWM' fans to the cable splitter but, of course, l assume all 3 fans connected would run at full speed (unless your motherboard 'DC' mode may be able to still control them).

The quality is excellent, However the cable could have about 5CM more so that it does not get so tight.

I buy two of these so I could chain link them together to run five fan on one fan header, of cause you can control the speed of the fan this way, they are worth every penny and works with my five case fans, will buy again

Excellent quality PWM fan splitter and should be an essential in any water-cooled builder's toolkit. Allows 3 fans to be controlled from one PWM MB header (I used for 3x120mm fans on my large radiator). Connectors can prove bulky when cable routing, so best to install this first and route through tray grommets before attaching fans.

Does the job well.What more can you say?Good quality construction - looks like it will last.

Only one of the cables has the 4 pins for pwm (labeled with white sticker) the other two gave 3 pins. The cables are a bit short and hard to bend easily. Works okay

Previously bought another PWM splitter but it did not function correctly so went for this from EK.Allowed me to control my three radiator fans from one mobo PWM point.Great quality as always from EK

Works great. Not much to say, it's just a fan splitter. Bought this because the 360 AIO I bought used locally didn't have it in the box.

It's slightly short but it's good quality. I decided to borrow one from a friend and it was great. Would reccomendPros-good quality-3 adaptersCons-slightly short

Habe ich mir für mein NZXT H9 Flow Gehäuse geholt um alle 10 Lüfter am Mainboard anzuschließen. Gut verarbeitet, aber materialbedingt etwas steif.

Para la caja de mi pc necesitaba hacer funcionar tres ventiladores partiendo de un solo conector, y ademas necesitaba que el cable fuera lo mas corto posible. Este cable me vino perfecto para lo que necesitaba. Llego rapido y sin problemas en la instalacion.

Ho comprato questo prodotto per collegare 3 ventole sulla parte inferiore del mio case al fine di facilitare l'immissione di aria fresca all'interno dello stesso.Non c'è molto da dire se non che il prodotto funziona, sembra costruito decentemente e permette di controllare le ventole sia in DC che in PWM.Consigliato per chi non ha sufficienti attacchi sulla motherboard e vuole collegare delle ventole extra.Ottimo anche per il cable management visto che è completamente nero e facilmente mimetizzabile nel case