bestarc Pilot Arc Plasma Cutter, [LED Display][Air Sensor] 50A Plasma Cutter Machine 110/220V Dual Voltage, 1/2'' Clean Cut 3/4 Inch Max Cut, Post Flow Mesh, 2T/4T for Beginners DIY, Yellow

So far, it's performing well. I used it to cut 1/4" stainless and it was fast, clean, and as expected. Easy to setup. I just connected the power, air hose, and machine connections, along with the grounding clamp, and I was cutting fast. I had a Hypertherm Powermax 30xp that was DOA, so I picked this up to fill in on my projects while I get a replacement and this Bestarc works extremely well.

Folowing up from my last review. Standup company. I was a week outside of the manufacturer's standard 30 day warranty. Contacted bestarc and sent them the same pictures I posted here. Without any questions they sent me a new unit. If this one goes out, I'll just buy a new one and purchase the extended warranty next time. For the weekend hobbiest this unit is more than enough. Wish I could give this 5 stars. When it worked it worked well. Especially for the price. After just 45 days of using it one of the relays soldered into the PCB took a crap and shorted out. All I have predominantly used this machine for is 18-20 gauge sheet steel so its not like I was pulling much power. I didnt purchase an extended warranty, thats my fault. Is what it is. I contacted bestarc directly to see if there is anything they'd be willing to do to help out so if anything comes of it ill update this review accordingly. Pictures to show the issue mentioned.

This unit has the pilot arc feature, a must in my view. Other low cost units do not have as pilot arc and require a "scratch start" actually touching clean metal to start the arc. Also this unit is 110 and 220VAC compatible. Compact and lightweight, easy to setup. I was cutting within an hour of unboxing. I would suggest, buy the consumables when you buy the unit. It only comes with 2 spare tips. Also the air hose with the unit is cheap and doesn't have the quick connect fittings. I suggest buy a 10ft compressor hose as well. Otherwise, see the video of me cutting. Works great.

For an inexpensive entry level plasma cutter, this is pretty great. Now I will say, it is great as far as it's cutting capabilities and ease of use (and boy do I use it). There are a few reasons for 4 starts and not 5 though. 1. The handle part feels a bit cheap. Still, if you are just a small shop who needs to cut metal on occasion or a weekend warrior like myself, it'll do. If you are a shop doing a lot of metal fabrication, maybe spend a few bucks more on something more durable. 2. It claims to work with a small pancake compressor. I set this up immediately and yes, it does work, however a small pancake compressor is only good for small cuts with breaks in-between for the compressor to refill. I found that to maintain 45 PSI for what I was cutting, I has to set the compressor to 60 PSI and it ran out pretty fast. I changed to my slightly bigger 3 gal Harbor Freight compressor and it was waaaayyy better with the ability to cut for longer periods at a time. Just think of how long each blast will be and make sure you have a compressor that can keep up. For small holes and cuts, the pancake is probably ok. For larger cuts or long use cuts, bigger is better. 3. It can run on 110, but... you know. So I hooked it up to a regular 110 outlet and it worked great for light gauge metal. I worked my way up and by the time I got to lawnmower blades, it started having some issues keeping up. I switched to my 220 outlet and BAM!!!... it cut like a hot plasma knife through butter. Overall, know the application you will be using it for and make sure you have a setup that can accommodate. As long as you have the right power and air for the job you are doing, I have not had any issues with this thing keeping up. If you have been thinking of playing with plasma cutting but are on a budget and don't want to worry about gases and stuff, this is a great option.

This plasma cutter is amazing. Very easy to follow the set up instructions. I connected the leads, power and it came with a quick disconnect air fitting installed. Turned on & cut some 1/4” steel pieces and it cut very smoothly. I will need some practice to get proficient, but the first few cuts impressed me. Would buy again and would definitely recommend. Five stars!

This is a great non-touch plasma torch. The design makes it easy to set up all cutting parameters. It’s lightweight, with all external connections done without tools. It’s equipped with an air dryer, which should extend the torch expendable parts life. All controls are on the front panel, easily set and read, except for on/off switch. It can be flipped on or off from the front, once you know it’s located. I’ve cut metal with for years but I’m a first time plasma user. I quickly cut various thickness and conditions of steel, and found it intuitive how to set up the pressure and current. There’s a chart with recommendations, but I found thinner metal below 3/8” could be cut cleanly and quickly with the same setting. All you need to do is cut at the best rate, and that’s learned quickly within the first inch of cutting. I did find it more difficult to punch a hole through thicker metal with plasma than Oxy-acetylene (3/8” and thicker), but the thinner metal was as easy as Oxy-acetylene. I’m sure when I developed the proper technique, the thicker gauge metal will punch easily. I felt so confident after 15 minutes of playing with my new torch, I started and finished two projects I’d been waiting to do because my acetylene bottle was empty. With plasma; all you need is an air compressor, and electricity. And this unit will work on 110 or 220, and both have a 50% duty cycle. For my two projects I was cutting with 220, and it cut both 7/16 and 16 gauge quickly and cleanly by only changing air pressure and current. With Oxy-acetylene I would have had to change tips and played with torch settings and pressures as well. Plasma is so much easier, with no expense of gas, and bulk of the torch and hoses. I’ll never go back! If anyone that reads this wants to buy an Oxy-acetylene system lock-stock-and barrel call me;-).

Bought the biggest one and it has performed very well as it has cut up to 3/4” inch with ease. Using it on a farm so not used everyday to test for durability but I’m impressed with the capability of the machine.

Es muy bueno considerando el costo del producto, hasta el momento eh cortado placas de 12 mm de espesor sin problema, logicamente a 220 v, es un buen producto, muy recomendable

الجهاز ممتاز ماشاء الله والبايع جدا متعاون ويرد عليك بسرعه من اول ما ترسل له انصح به

I like the air regulator in the front of the unit making it easy to see and adjust. The water drain and connection at the rear of the machine is nicely protected from being bumped. I like that you can adjust the time the air stays on after making a cut greatly reducing the wear on consumables. The performance is better then a lot of other machines at this price point with a 60% duty cycle at 50 amps 220v but at 35 amps it's 100% duty cycle (60% duty at 35 amps on 110 and 100% duty at 28 amps at 110volt just for info). Lastly when I unpacked the unit, I seen the torch tip was slightly black from them testing the unit prior to packaging. Definitely better quality control then other manufactures I've seen.

Perfect and just what the shop needed. Quick delivery and in perfect condition.