Micro Drill Bits Set with Pin Vise | Small Hand Drill - Pin Vise Hand Drill Manual, PCB Mini Bits for Resin Beads Polymer Clay | DYI Jewelry Making, set

Very precise tool, works as described. Be very careful when using the smaller bits . If you flex them they will break. You have to be slow and methodical and put the item you are drilling on in a vice and that will help with the process. So far I have drilled wood and acrylic and both were fairly easy to drill through. About to try some harder objects and hope to have the same success. The bits are hard enough and very sharp so I think they will do a great job. If you need quality and precision I highly recommend these bits .

Item: Amazon 3” acrylic ornament disk with plastic protective film on each side.I am calling this tool a “Gizmo.”WHAT I TRIED TO DRILL HOLES IN AN ORNAMENT BLANKFirst fails: battery powered screwdriver with drill bit. That cracked disk and half went flying across the room!Second not great result: Dremel 200. It did sort of okay but hole looked chewed up. I had to clean it up with a vise. Called Dremel and was told to use a 4300 and go buy Dremel drill bits and get a drill press stand. ( Before I invested $250 for the set, I wanted to test this $10 gizmo!)THIS LITTLE GIZMO: Huh! It WORKS!It is VERY s l o w, but not hard to do. Downside to do the 36 holes I need would take about 9 ( nine!) hours. First hole took about 15 minutes to break through, but it was a pretty clean hole! Compare it against the machined one I didn’t do on right.I used the largest bit in the set. 1/2 way through the bit slid up inside the gizmo. So I had to fish it out, put it back in position and retightening it in jaw.Emphasizing “Used largest drill bit.” Look at the holes: the one on left this Gizmo did. The one on right the ornament blank came with it.Large = about 1/8” hole.Smallest bits are smaller diameter than a sewing pin.Conclusion: This takes A LOT of patience! If the goal is to finish fast and finish your project, like I wanted to do, this level of “slow” is too slow. I am going to source a colleague with a Dremel 4400 set up and pay them to do the drilling. With the right set up, should take about 15-30 minutes.But if you want a project while watching tv, or waiting on a meal in the oven, or hanging out watching your front lawn grass grow, this slow Gizmo does work.Dremel’s are worth the investment when multiple projects are waiting. They are great little all in one tools for small projects.Tip - unscrew the Gizmo part closest to jaw to open so you can put in drill bit. Instructions are not correct in web page; it says to unscrew top area. No Instructions on box, just warning to wear glasses and bits are fragile.Bits may be stuck in storage tube. Mine were. I dislodged a few using another bit. The tiniest ones were really stuck! I took off cap from other end and “blew hard.” That moved the last two a little bit to wear I could scrape them out with another bit.

Package arrived next day as promised, (thank you!) and product undated. This is to be used in model building of a 1/350 scale USS ENTERPRISE production style.• PROS: The holder is easy to handle; putting in the bits in takes a little time to get used to, but easily learned. The mico bits are separate from the regular bits, and well protected by a heavy gage plastic case. The regular bits come in a plastic tube with stiff rubber ends that are pulled off by hand. I did use this to open up a few extra holes wiring this project for lighting, and the product worked fine.• Cons: Though the main storage case is easy to open, the micro bit case is a little difficult. (I’ll try to remember to attach a pic) Once this case is opened, the bits are nicely stored in a holder; but, I wish that on the place that looks like it could’ve been used to put each size is blank. I understand that there is a measuring gage on the front of the main storage case, but who wants to take the time to measure each one during a build? 🤷🏼‍♂️ This should’ve been taken care of right off the bat at the company. They are color coded, but I still would like to see the size up front. I wanted to know where to purchase replacement bits (just in case) but the “scan me” icon takes you back to the original Amazon page where you purchased it from; I couldn’t find any replacement statements, and when I asked the question on this page, the company only wrote, “Yes, you can purchase replacements”, but nothing else. The other icon to scan on the front of the main storage box takes you absolutely nowhere. 🙄 I thought it may be a tips and hacks for this, but apparently not.• PLEASE NOTE: Let the bit do the work! Don’t press down, or try to hurry the process up. I haven’t broken one as of yet, and hope that I don’t; but I can see where it would snap easily due to the size. When you open the regular bit tube, do so over a towel or similar; though I say, “regular”, they aren’t you everyday drill bits from Lowe’s or Home Depot. I was using the term regular to denote these not being the color coded micro bits.The idea I’m going to use since I have a regular workbench is making my own holder. Using a piece of pine, I plan on measuring each one, and drilling holes in one line to fit (bottom first) each micro bit, then a line for the others. Then take my brother label maker and mark each one. Just a thought… 🤷🏼‍♂️😄🪛 (Pic now attached as #3)Thank you,Doc LykinsVirginia

Really excellent tool for my models. It's effortless. Great choice of sizes. Great shipping and was really happy I was able to help a family owned business.

This micro drill bit set with pin vise is extremely versatile and gives you full control over both the hole size and its exact position, something you don’t always get with power tools. It comes with a great variety of drill bit sizes, perfect for detailed work in resin, plastic, or small DIY projects.What really impressed me:Even though the description doesn’t mention metal, I used it to drill into the metal cover of a Wireway, and it worked perfectly! Clean and precise hole with no issues. Totally exceeded my expectations.Highly recommended for detailed or delicate work, and even for some light metal drilling!

OUTSTANDING! I can't believe I waited this long to buy. I was using using 3/8 electric drill. It was clumsy very difficult to use. It's back in the garageThis is a great price, the quality is good.