VADANIA Blind Corner Swing Tray Organizer, 800mm Right Handed

I was a little bit skeptical of these as they seem to be about half the price of similar units available elsewhere, however I needn't have worried. The units are solid and have a smooth action, they self-close without any issue and fit a decent amount of stuff on them - not as much as standard shelves but enough to feel like you are getting a net benefit from not having unusable space at the back of the shelf.I can't vouch for how easy they are to assemble as my kitchen fitter assembled them for me... badly! Upon assembly the shelves were wobbly and wonky but that was an installation error rather than a product fault... maybe the instructions for assembly aren't great - It was obvious where the kitchen fitter had gone wrong and I was able to correct his errors within 30 minutes, after which i now have rock solid shelves that I am fully happy with.

Excellent product, very sturdy and well made, however, instalation was not so easy. I called in a flat pack furniture assembler and it took him 2 hours to install, he had to physically get inside the cabinet , fortunately he was small but still struggled to get the main support fitted.

I'm writing this review mainly because I saw some criticism of how this thing fits or doesn't fit, and if it fits standard units, and how poor the instructions are most of which I found to be completely untrue.It does fit standard units, and the instructions are quite adequate.The only wrinkle I found was the dimension given for the distance from the end of the cabinet to the hinge point (470mm, for a 1000 unit) wasn't possible with my centre post. But this measure should really be given as a range, say 470-something over 500mm. I was able to keep the shown distance to the front of the until and fitted it as close behind the centre post as possible. Note that fitting the top shaft fixing is always going to be quite awkward unless you are doing it with the worktop removed! consider that on a new installation!It all fits and works well. Quality seems extremely good.All the parts were there but some screws were lose in the box and not in the plastic bag.Note how these things are sold under a few different names, and they play a game with purchase price and shipping that makes total price very similar whichever you buy.

Once fitted, item worked great, the tolerances were very good. Clean finish and seems to operate consistently well. Although I found the instructions to be a bit confusing. If you don’t have standard measurements, you have to be comfortable with adjusting the vertical pillar to find the best position.

SUMMARY: DON'T BUY IT, IT'S NOT WORTH IT-> It's a poor-quality product.-> Assembly instructions are very confusing.-> Instead of helping you make use of your blind corner space, it makes it almost unusable.-> If you really insist on a pull-out solution, do yourself a favour and go to B&Q instead. You'll save yourself a lot of time and stress. You can thank me laterFULL STORY:A little context first. I installed a blind corner kitchen cabinet from B&Q recently. We have a small kitchen, so I wanted to use that space efficiently and also avoid getting on all 4s every time I need that deep pot. I saw the Pebre pull out system in B&Q and I loved the idea. Unfortunately, I am cheap and stupid, so I found this Vadania product and decided to save some money...The problems started right after unpacking. The assembly instructions are very confusing. It's relatively obvious how to install the pole on the left-hand side but good luck trying to figure out the right place to attach the panel on the right-hand side... I found the manufacturer's video on YouTube, but the measurements for the placement of the panel were different between the video and the instructions included in my package!After I finally figured out how to install all the arms, I tried to place the shelves on them. No luck! One of the bolts went into the bearing quite smoothly, but the other one wouldn't go in at all. I thought I was doing something wrong, maybe not aligning or not leveling the shelf correctly. So I removed the arm and tried to place it on the bolt while the shelf was upside down, so I can see everything and align it correctly. Still no luck! I've put some pressure on it, the bolt went into the bearing a little bit and got stuck! FFS...The bolts on the second shelf were better so I managed to install that one. I decided to see how it works before trying to install the first shelf again. Here comes another issue... I realized that the shelf is super small, which combined with its awkward shape makes it pretty much unusable. It's not even big enough to put a dinner plate on it, let alone a couple of frying pans. I mean, you can put them ON the shelf, but they don't below the rails... FFS!The bottom line is that while trying to save 100 quid I wasted 200... The shelves are completely useless. I have thrown them away and installed a normal shelf. It's less convenient to access but now I can actually use the cabinet space efficiently.The pull-out system sold in B&Q seems to be better. The shelves don't have high rails so it should be easier to place items that don't fully fit within the shape of the shelf. However, I'll stay with a normal shelf for now.

This is an excellent piece of kit to allow use of an otherwise wasted space in the corner of a kitchen. It removes the need for corner cabinet, which I don't like, and lets you use a 900mm or 1000mm standard base unit. It then gives you access into the 'blind' end of the cabinet with it's kidney shaped pull outs. I fitted one of these of a well known brand in my wn kitchen, but for my in-laws I chose this as it was over £100 less expensive. The quality, however, is no different. This does exactly the same job, but actually has a better soft close mechanism than my own.The only issue I had was that the instructions left a lot to be desired. They were just wrong, so I spent a lot of time just looking at them trying to figure them out. Because I had experience of this type of product, I had a head start. Not having experience could be very frustrating. In the end, I used the dimensions on the instruction (where to drill holes, etc), more as a suggestion than a mandate and after a couple of attempts, got the central post around which the mechanism rotates into a good position for the cupboard into which I was installing it.If you are DIY minded this is an excellent product. If not, you may end up pulling your hair out.

Good for corner units with a tight opening. Came well packaged and looks good once installed.The instructions however are awful I followed the instructions exactly and ended up being 2 inch’s out. Not sure if they’ve altered the design or something but it’s easy enough to install without needing the institutions. Just set up the central column and then just screw everything in where it lines up once assembled.Once assembled it’s rock solid and moves smoothly.

A good, well made and sturdy product, but the assembly instructions are simply a series of drawings which are it very difficult to determine relevant measurements. Also, I found that by trying to follow the flow diagram of instructions just made it far more complex and inaccurate.I installed the right hand pole, and arms first rather than the left hand bracket (assuming a left hand opening cabinet). The critical measurement for the pole, is 4850mm from the left hand side of the cabinet, and then 50mm in from the outside edge, both for the bottom and the top fitting. These measurements are where the centre screw should be located. Once this pole is secure, temporarily attach support arms to the left hand bracket, and adjust the whole assembly so that both sets of arms are level with each other. Now mark off the height from the bottom of the cabinet where the bracket should meet and secure the bracket to the left side of the cabinet. Once this is secure, it is then simply matter of attaching the trays to the two sets of swinging arms.