FOXBC 2 Pack Planer Drive Belt 5140010-28 Replacement for DeWalt DW735 DW735X Planer

This belt works perfectly but it is quite a challenge to get on! You will have to have a squeeze handle type bar clamp long enough to reach from the pulley to the base. It's possible to do, but be sure your prayer life is in order before beginning the project.

This was a good fit.

It is criminal what Dewalt charges for a replacement belt for their planer. I decided to give these a try and with there being two in a package, I figured I could replace them every 6 months for 5 years for the price of a single OEM belt if they turn out to be lower quality. So far, with light use anyway, the first one seems to be working and holding up just fine. I do not know how this compares to the OEM version but it was quite a PITA to get it on. Makes me wonder if it is slightly shorter or maybe stiffer than the OEM version.. It probably took me almost an hour and several different tries to finally get it on so I sure hope that it lasts as long as the OEM one did (about 10 years). I actually bought an OEM one too just in case this one didn't work out but never took it out of the packaging so I could send it back if this one worked out ok. The OEM did seem a little less stiff inside the flexible packaging but not significantly.

Good value

Perfect replacement. The original belt melted after a jam that tripped the breaker. I forgot to turn it off first, so when I reset the beaker and walked back it melted! The replacement was pretty easy and straightforward, not nearly as complicated as some videos make it out to be. TIP: attach the belt to the small pulley first, then “start” the belt on the edge of the large pulley and turn it with a socket wrench. It will feed itself on and you’re done. Just make sure it is fully seated, and watch your fingers while you adjust it lol.

I decided after 8 years it was time to swap out the oem belt for a new one after it started slipping. I come across this pair of belts and thought it would be nice to have a spare. I installed the first belt and before I could even get one board through I smelled hot rubber so I shut the machine off and looked and the belt had ashtray walked itself off and began to melt. Keep in mind this was in less than 60 seconds. So with frustration I disassembled everything I had just done and realized the belt had melted itself into the groove as well. So after a hour of scrapping I now had both pulleys clean I reinstalled the second belt with hesitancy but I was in the middle of a order so it had to work. I have now have run about 200 bf of cedar through and noticed a ticking noise. So after removing the side cover to no surprise the second belt had began to melt as well. So I ordered a new pulley because it's not worth the time it takes to scrap the sticky rubber off. I received the new oem belt and pulley installed them and ran the rest of my cedar and about 500bf of oak with no issue and no signs of wear. So please take my word and do not buy these belts they are very cheaply made.

I have installed after market V-Belt just like this on many centrifuges in laboratories all over So-Cal. And, frankly I was appalled by the YouTube "How To" video's out there. One guy was poking around with a screw driver, forcing the belt on. Another was a guy removing the keeper, gees talk about making it ever harder to reassemble. Those two wouldn't have lasted long as a Biomed. The secret is to remove everything: side cover, adjustment wheel, chain tensioner, pulley sprocket /with chain (pay attention and put this back exactly the way you took them off, pull straight out, turn face down and reverse for the install). Put the V-Belt on the upper smaller pulley (remove that cover if you haven't already done so) and then firmly hold the belt to the lower side of the larger pulley and gently insert a socket (I recommend 3/8" drive or larger, 1/2" drive even better) and slowly turn the pulley clockwise until the belt slips on. Weighing in at 92 pounds, no worry about holding the planer.

They fit perfectly. It seems like they’re too small but they’re the exact size of the original, they’re just a different color. INSTALLATION TIP Don’t use a screw driver to install. Use your thumbs. It will hurt. First you need to take off the chain and sprocket. Also take off the spring and wheel that hold down the chain. Put the belt all the way on the top pulley first then gradually rotate the belt on the lower pulley from the top of the pulley. Push the top part of the belt so that the V grooves face away from you and rotate the lower pulley clockwise all while keeping tension on the belt. Keep doing this until it’s fully seated. The belt slipped off the top pulley a little and I had to push the bottom part of the belt towards the machine and rotate the lower pulley clockwise to fully seat it. Hope this helps!

The product is a very good item, with exact measurements, and quality materials. It was delivered promptly.

Product works as described

Works great , I hope it last as long as the original one 20 plus years

Bought as spares.

1: un objet a tombé dans le planner. 2: j'ai contacté le problème: 3: j'ai commandé la courroie: Bien. 4. J'ai nettoyé les obstructions fondues 5: j'i installé la nouvelle courroie. Je n'ai pas vérifié la réparation. 6: 6 mois plus tard, j'ai utilisé planner sans même vérifié et pensé qu'il avait subit une réparation. J'ai planner des grosses pièces toute la journée. J'ai pensé plus tard qu'il avait subit une réparation. délicate. Avec des bonnes pièces de réparations et une bonne méthode de travail. fonduessur les 3. J'ai r