ソフトレリーズ シャッターボタン ブラック Fuji Fujifilm X-T30 III X-E5 X half GFX100RF X-M5 X-T50 X100VI X-E4 X100V X-T5 XT5 X-T4 XT4 X-T30 X-T20 X-T3 X-T10 X-Pro2 X100F X100T X30 X20 Nikon Z f Df Sony RX10 IV III II

他のものはすぐ外れたりするけど外れない緩まない。 デザインもシンプルで押しやすくて良い

黒に赤で、シックで良いです。 が、ちょっと分厚いので星4つです。

かっこいいデザインで気になっていたが別の物を付けていて見送っていたが物欲に負けて購入。 ネットの画像以上にかっこよく現物をカメラに付けて眺めるだけでにやけてしまうぐらい大満足。 良い買い物が出来た。

X~M5で使っています。見た目は良いと思いますが、しっかりねじ込んでもややガタつきます。油断していると緩んでいることも。また、シャッター半押しがしにくく、シャッターの実用性は明らかに低下します。

デザイン、質感共に良かったのですが、2週間位で行方不明になりました。 これまでも2.3個無くしたので、この製品が特段悪いと言うわけではないと思います。

シャッター押しやすく大変良いです。

ゆるかったのかすぐ取れちゃう

色も手触りもいい

Excelente e necessário. Funcionalidade no momento de acionar o obturador.

Bien. Esthétique et fonctionnel. Pour mon Fujifilm XE5. Correspond à ce que je cherchais

Got mine Jan 2019 and just lost it on my most recent europe trip! Thats almost 6 years! Throughout the years it became looser and looser and I had to constantly tighten. Had a few times where I thought I'd lost it if I stored my camera in a pocket or bag not the camera case I would use for long term storage. So like anywhere else that had would brush up against the grip to loosen it while on the go. It became a little ritual thing, before every shot, I'd run my thumb on the release side grip (which was very tactile and responsive) then position my hand on my hotshoe thumbgrip then pointer finger half press if I was on autofocus and click~ After shooting I'd reverse and end with running my thumb on the shutter release again to tighten via side grip and turn off the camera. I have it on a fuji x100V (previously on a a fuji x100F) so it's been on 2 cameras! It was great! May repurchase, I'm going to keep looking around amazon, but wanted to review because it was absolutely a great purchase!

Not sure what others received in their mail, but this soft release button is amazing and it fits X-T3 like a glove. Maybe they should check item description before placing the order, simply to see which cameras this button's thread is made for. Not all cameras use the same thread and diameter. For X-T3, I can guarantee it fits perfectly. It comes inside small packaging with two o-rings included (one is just reserve). Inside the small manual, it clearly states that O-ring is needed for Fujifilm X series cameras, and that Sony RX1 and RX10 don't need it (little longer thread inside the camera's button). Also, don't think you will not need that O-ring. It's not there just because they said it's needed for Fujifilm X-series cameras. Its main purpose is to act as a spring. Once you tighten your soft release button to the camera's shutter release button, O-ring will compress a bit, and it will push back against the soft release button, holding threads of the soft release button tight and secure inside the shutter release button of the camera. There is simply no play, it stays there once it's properly installed, and it's not moving left or right, unless I wan to unscrew it. Even then it takes some force to do it. Falling of the camera by itself? Nonsense. Some other people mentioned using loctite glue, gorilla glue, crazy glue and whatnot. Who wants to ruin their camera they paid with hard earned money by burning it with those chemicals?! I sure don't. Simply install that O-ring properly, there is even quick tutorial in few pictures on how to do it properly. Even though it might seem non-important, for sure IT IS important to install it properly. Follow those few simple steps they provided on that little paper that came inside the box, and your button will stay there without falling off. I am talking about X-T3, can't confirm for other cameras, X-T3 is the one I have and use this soft release button with. Have a look at the photos I attached, you can see how it fits and looks like when installed. That amazing looking knurling around the soft release button matches the knurling of the X-T3's buttons. It looks amazing! April 23rd update, 17 days later... release button sits as tight as I left it when I mounted it on April 6th. After heavy usage of my camera (in photo and video mode), I can confirm this button stays where you put it. Note: you have to use O-ring provided with the button. It will serve as a spring adding additional resistance against the thread. Amazing product, would purchase again if needed.

A nice little addition to the camera and it gives a better overall feel when using it. It fits well, looks good. It comes with two rubber rings. So far, I’m happy with the quality and first impression. I’ll update the review again after a few weeks of use.