Grafix Clear Craft Plastic .020 Thickness 8-Inch by 8-Inch, Pack of 4

I purchased these not knowing what I was going to get. I had been looking for thin clear sheets to create foregrounds in a deep shadowbox. Plexiglas was an option, but it was too thick and far too expensive. And the only places that would sell it never had a guy available to cut the dang thing. So I searched on here for something that could solve my problem while staying in budget. Upon ordering, I had worried about the product having faulty cuts and having to correct them myself, but it was for nothing. These were cut perfectly to size. And even if it had been cut wrong, the plastic was easily thin enough to trim with scissors. The sheets were 100% clear and clean from scratches. My project came out wonderful and I still have a few sheets left over to use in the future. I'll definitelyorder these again should any project require it.I'd highly recommend this for crafting and scrapbooking, Great quality, great price, great product.

This worked well with my Cricut Maker 3. Cut easily.

Bought this for my Aunt's work, but she loves them because of the consistent quality. Tight tolerences are important to ensure the many hours spent on her intricant work are not wasted. The value for the package is surperb. They were discontinued by national chain(s) but thankfully Amazon still sells them at a great price. They're also made in America unlike some others. 5 stars.

Super nice sheets of plastic. They're not advertised as laser cutter compatible, but I tested them and they are! I did the "chlorine test" with these, melting some onto some copper, and then putting the copper into a flame. It did not burn green! So it is safe to use with laser cutters!So I made a stencil on my laser cutter, using the engrave setting to burn lots of tiny dots (like a wire mesh), and the plastic mostly did well, but got a little melty, had some warping in areas that have a lot of engrave heat on them, so be sure to hold down the edges of your piece before lasering!Grafix recommends their "Dura-Lar Film" for laser cutting, so I think for this Clear Craft Plastic, using laser cutter is maybe "off use" - if I had to guess, maybe because of the warping. Giving this 5 stars because it's great plastic, for most people. For laser, I'll give it 3 stars because of the warping, but that could be my settings and inexperience. :)

The media could not be loaded.  Worked perfect for my cricut maker. I used the basswood setting which I saw recommend by many but on that setting my machine seemed to cut it too easy! It only took 6 passes and I probably could've stopped at 4 or less! Knowing that I'm definitely interested in trying out a thicker acrylic sheet to see if my knife blade will cut a little thicker acrylic since it seemed to cut this almost too easily. It is thin but not too thin to where it's flopping around after being cut. I thought about using it for Keychains but after getting it I think it's probably too thin for that.

This is very durable craft plastic and my Cricut cuts it just fine! Great price and quality!

I had seen where people were using this in their Silhouette Cameos to cut out stencils. I have had the hardest time trying to get them to cut...HERE'S WHY? I'd been using the blade that has been in my machine for about three years. I don't do a lot of cutting, that's going to change now because I've started making cards.YOU MUST HAVE A NICE SHARP BLADE, PREFERABLY A NEW ONE!I didn't realize how dull my blade was, but I had an unused one so I changed to a new blade and VOILA! it cut right through...in fact I cut a hole in my mat. I was just cutting a 1/4" square to see if I could make it through and I still had my blade set at 10, so it cut through the plastic and the mat. I changed the blade depth to 5 and it cut almost all the way around a design, but a few spots didn't cut and made getting the stencil out a little difficult. This is rather thin plastic and a little on the fragile side, so you want the blade to do all the work and not have to bend or damage the plastic manually. I changed the multi-pass to 3 times and it worked like a charm. Pulled up the plastic sheet and the stencil stayed on the mat, one piece and was easy to remove with the metal spatula.Since I'm going to be making 6" x 6" stencils each sheet of this plastic will give me 4 for a total of 100 stencils out of the 25 sheets...a bargain!I've included the cut settings below for those that want them. REMEMBER! NICE SHARP BLADE, PREFERABLY NEW!Silhouette Cameo 2 - Cutting SettingsGrafix Clear Craft Plastic .007 ThicknessBlade - 5Speed - 4Pressure - 33Multi-Cut - 3 passes

I'm in the process of unmounting a bunch of stamps on wood blocks to save tons of room. This product works great and is the same thickness as the plastic on the stamp sets I've already purchased that are either cling foam or clear stamps (Penny Black or Hero Arts, for example).I'm using Grafix 9-Inch-by-12-Inch Cling Film Clear on my old stamps and it sticks perfectly to this plastic (I nuke them briefly in the microwave to separate the backing from the wood). For those stamps that have the sticky foam already attached, I put them on the cling film and they stick perfectly to this plastic. On old stamps where the rubber separates from the cushion, I use Aleene's Tack-It Over & Over on them and then put them on the cling vinyl and then on the plastic. I just received my Amazon order yesterday and have made good progress towards my goal of freeing up room for my ever increasing purchases of stamps.To easily keep track of what I have, I stamp an index sheet of the images and store them in Avery Elle Stamp and Die Storage Pockets, also available on Amazon.

Bought to make stencils with my Brother Scan n Cut. Works great! Not too thick, but thin enough for purpose.

Llegó en tiempo, forma y en excelentes condiciones, tal cual a la descripción, excelente calidad. Contenta con mi compra

I have bought this wonderful product before and find it exceptional. for glazing my 1/43rd scale tramcars.

Produit se découpant facilement avec la maker

Used this with a knife blade and my Cricut maker and made a cake charm and a number topper. I can’t find this acrylic in the UK but fortunately Amazon US have it. This 020 acrylic is the thickest acrylic you can successfully use with the Cricut Maker, I tried and 040 and it’s too thick. It only takes around 6 passes to cut really well. I then overlaid the topper and charm with adhesive metallic foil.I’m a cake maker and these charms and toppers are so expensive to buy so I’m really happy I can make them myself.