EcoSmart ECO 18 Electric Tankless Water Heater, 18 KW at 240 Volts with Patented Self Modulating Technology , 17 x 14 x 3.5, White

Great! Easy to install if you’re familiar with running electrical and minor plumbing. Definitely would run a filter on the inlet side. Installed a 18kw unit in SC (inlet temp 62f) and have no issues! Water is hot, and I mean HOT. We use high sierra low flow shower heads already at 1.25 gpm, so even though we shouldn’t be able to, we can run 2 showers with no problems. It’s super convenient to have unlimited hot water and not be heating a 60 gallon tank 24/7, using only what we need when we need it. Flow wise; it’s a bit slower, but it’s more consistent than before, not having to adjust valves as you run the kitchen sink as someone is showering. Definitely worth the money, especially since it’s less than the cost of a 6 gallon point of use tank from Home Depot or Lowe’s.

Installation is fairly straight forward. Included instructions book is very helpful. Keep it for future troubleshooting because there is detailed information within for any faults encountered. I kept the Eco within 5 feet of my main panel to keep the wire runs as short as possible.. I like the design; all connections feed through the bottom and front panel is easy to remove without disturbing wires or plumbing to access inside as needed. LED display remains dormant (off) until unit detects water flow and then pre-set temperature is displayed while water is running. LED display shuts off a few seconds after water flow stops. Using an ordinary kitchen cup, I measured the minimum water flow necessary before heating elements turn on being ABOUT 2 quarts per minute. Heating elements remain dormant unless it detects water flow higher than that approx quantity. Instructions clearly suggest keeping pre-set temperature around 115-120 (F) degrees. FOLLOW this guideline. I experimented with hotter temperatures thinking the quality/consistency of hot water would be better. Actually, having the pre-set too hot is counter-productive because the faucet water will be too hot, you'll be throttling back to a colder setting at the faucet, and (here we go again) there won't be enough water flowing through the unit to turn on the heating elements. Then you'll be constantly adjusting the faucet handle(s) in efforts to get a stable temperature. Keep it at 115-120 and you'll be quite happy. I live in South Florida and the coldest weather we've had this season dropped the incoming cold-water temperature to "only" about 60 degrees on that "cold" morning. So to "stress" the unit, I turned on 2 showers, 2 faucets, full blast, and the washing machine (all at the same time); the ECO 18 had no problem keeping up with the hot-water demand. If your incoming water temps (are lower) and usage quantity (is higher) than my baseline, you'll have to experiment for yourself or talk with the tech assistance line.Cons? - - Only arbitrarily minimal. My Eco-18 has a pattern of making really hot water, then warm, then hot again as it stabilizes just as the faucet/shower is turned on, only at beginning (eg. Mornings). I verified this by asking a family member to turn on a tub faucet as I measured the temperature at the copper "water-out" side directly near the unit. I can also tell by the way the bathroom lights dim ever so briefly (twice) as the initial electrical surges hit the power panel. After all, the TWO elements pull about 37 Amps EACH at initial start-up. It takes about 7-10 seconds for the unit to stabilize it's temperature output (and the bathroom lights remain at constant brightness); but I can live with that. It's no major complaint. If there's any critics out there: 1.) Yes, I installed all electrical as per NEMA standards, 2.) Yes, my main panel is rated for this amperage with plenty reserve capacity, and 3.) Yes, I installed a separate 100-amp subpanel with two 40-amp breakers dedicated to this water heater (as described in the installation instructions) using (overkill) 6-gauge wire as a safety precaution.Pro's? - - Small package size, space savings compared to a conventional 40-gallon tank. Hang it on the wall, make the connections, set it once and forget it. "Hot water forever." On a side note, South Florida water is quite hard. Curiosity got the best of me with the old tank-heater. I cut it open and discovered a 4-inch thick layer of calcium deposits on bottom of 7-year old tank. How does this relate to the Eco-18, you may ask? Well, since water flow through the Eco-18 is at a high velocity, I have a feeling that calcium deposits cannot collect within unit.....so it will last a looooong time. Time will tell. The one-year duration for my household has proven successful thus far.Middle-Ground Opinions? - - There's lots of talk about energy cost savings. Well...<pause> (?) ...I did a comparison of my household's last year Kilo-Watt usage to this year (month by month) and did not notice any consistent measurable savings. Of course, there are variables to consider such as growing kids, the time they spend in the bathroom preparing for the day, and how much laundry ends up in the hamper every other day. All this tends to increase as teenagers get older. The only quantifiable fact is that the Eco-18 does not consume power while at idle...waiting for the next person to turn on hot water.Despite the lengthy narrative, I'll give the Eco-18 a number "9" on a scale of 1 to 10. A small human learning curve and adaptation is necessary to live harmoniously with the heater. Be sure to have the temp pre-set to 120, be aware that a minimum water flow is necessary to "wake the heater up", and don't be nervous about the lights dimming temporarily as the heating elements energize. ...enjoy. :-)

2nd one of these we have bought, we live in Northern ga and it keeps up with a family of 8 (4 adults 4 kids) we can take 2 showers at a time on opposite ends of the house and it produces amazing. And let me say I take lava showers and this hot water heater don't disappoint.

Had my ECO-18 replaced a few weeks ago after it suffered an internal fire sometime during the night, despite no use of hot water. Fortunately, the circuit breakers eventually shut-off the electrical power and the unit was mounted on a masonry wall. The unit was professionally installed 3 ½ years ago.No idea why this occurred and ECOsmart support stopped responding to my questions or request to speak with management after I sent them photos. The last use of hot water would have been just before retiring for the night and perhaps the unit simply continued to heat without any water demand or it had a sensor fault during the night that caused the power to activate the electrodes. When I walked into the garage in the morning immediately after experiencing “no” hot water, the smell of an electrical fire was evident. We were preparing to leave on a week’s vacation, so I only had time to completely disconnect the unit from any potential electrical power and make sure there was no potential for re-ignition.While on vacation I ordered a replacement ECO-18 from Amazon and had it shipped to a neighbor. I also had an electrician and plumber schedule for when we returned home. The decision to replace the unit with another identical unit was to minimize the time without hot water after we returned home and provide time to determine what to do about the failed ECO-18. The very first task after restoring hot water was to install a Smoke & Carbon Monoxide detector near the ECO-18.While the Plumber was on site, I asked him if he could remove the electrodes for me since they had fused to the copper jacket during the melt-down and fire. It was evident the problem had started with the first electrode. He was eventually able to remove both electrodes. I thought the electrodes might show signs of calcification as a reason for the unit failure despite (3) upstream filters, including a de- calcification filter and last rinse 10-months prior. However, both electrodes were very clean.I noticed one significant difference between the “old” and “new” ECO-18 water heaters. ECOsmart has completely replaced the Flow/Sensor unit on the “new” ECO-18, as well as, the piping design to the Flow/Sensor. I am speculating the original Flow/Sensor had been experiencing problems so the company replaced it with an entirely different design and placement of the Flow/Sensor. Perhaps the old sensor was reason for my ECO-18 melt-down and fire but I’ll never know because they refuse to respond to my requests for a response. Perhaps they are concerned over Product Liability issues.

Delivers nice hot water on demand and haven’t had issues with not having enough hot water. Frees up needed garage space . Would def buy another!